Q:What's the difference between a rubber belt and a polyurethane belt?

The rubber belt and good flexibility. Good water resistance and water resistance..PU reciprocating work is poor. The high and low temperature performance is poor. Good wear. At room temperature under static conditions. Conversely PU rubber.

Q:How to distinguish sanlux rubber belt quality

The fixed belt conveyor adopts a fixed bracket, and usually the outer end of the roller on both sides of the groove support roller is deflected from the direction of the conveyer belt to form an angle. In this way, because of the existence of the idler angle, the lateral roller has a certain lateral thrust on the running belt. When the belt is in its normal position, the thrust force on both sides is equal in magnitude and opposite in direction. Once the deviation, deviationThe lateral thrust of the side is greater than the other side, and the belt is restored to its normal position under such lateral thrust. It must be pointed out that the relative slip between the belt and the deflection roller will lead to wear of the conveyor belt. Therefore, the angle of the side roller can not be too large, generally 2 3?. Therefore, this method is only effective for the condition of little deviation.

Q:What sectors does rubber drive? That is to say, what are the main uses of rubber?

Cars, railways, shoes, wires, cables, new materials, many

Q:How to clean rubber band?

Last winter I bought a stainless steel basin. I baked it on the heater. It was easy to remove the label, and it didn't leave any trace.Recently, I have encountered similar situations in my work. I found that the method of wiping with alcohol is better, or it can be removed with an eraserThe newly bought stainless steel pots or glass stick on some labels, off the labels, stickers on the traces of it is difficult to remove, wipe with a damp cloth, scraping knife will often leave traces, after repeated practice, I summarized some tips to share with you.On the hard surface of the self-adhesive mark, we can use non greasy wash water on the surface of the object, and then gently wipe with soft cloth; with industrial alcohol or gasoline can also remove these traces. If these stickers are found on the skin, they can also be removed with lemon juice.In addition, hand cream can also be achieved to remove the effect of self-adhesive, hand cream contains a lot of water (generally more than 70%), water contains a certain amount of surfactant. Surfactant has good wetting, permeating and dissolving ability. It can quickly penetrate between the adhesive and the surface of the object, so as to achieve the goal of cleaning. You can also find some similar products, such as creams, facial cleanser and detergent.

Q:The rubber strap is a little tight, is it better or a little loose?

Generally speaking, men's wear watches do not overtighten but not too loose, it is best to wear after can be part of your wrist bone block does not decline (wrist bones are small and larger) bone behind tend to fine down where you can send some will say that gap does it mean to have a finger said after wearing in a small range on the floor but more close to the standard.

Q:What do you call a machine that folds rubber bands into a stamp?

The word "mechanical" in modern Chinese is the generic term for "Mechanism" and "machine" (Machine). Mechanical features are: machinery is a combination of artificial physical components. A definite relative motion between the parts of a machine. So the machine can convert mechanical energy or perform useful mechanical power, is the modern mechanical principle in the basic concept, the modern concept of multi-source Chinese mechanical word from the Japanese "machinery", Japan's machinery products do the following definition of mechanical concept (that is consistent with the following three features called Machine).

Q:What kind of rubber belts are there for sporting goods?

The two characteristics will minimize the pressure on the joints during training and effectively avoid damage to other parts during training. The biggest advantage of the progressive training system is the difficulty of training, that is, the magnitude of product resistance can be gradually improved with the improvement of the patient's rehabilitation and strength

Q:Why are the engines almost all rubber belts?

The main reason for the belt is to prevent overload, because when the load is too large, the belt can slip, and also can start slipping, reducing the starting shock.

Q:White rubber strap dirty, how to do?

Now clean the strap. Clean the surface of the strap first, then clean the stain in the band gap. The gaps are so tight that it's difficult to clean the dirt inside. Now the gaps are opened up by the cylinder, and the dirt can be cleaned.

Q:What should I pay attention to when the belt conveyor is setting the brake?

Feedback the next level of inclined belt conveyor control speed, when the speed and load force of rubber belt motor is higher than the synchronous speed, the generator drive motor will effect the speed limit in normal running speed, when the motor is accelerated to a certain speed, and the speed of the output current is too large, the overload protection device to cut off the circuit, the motor will lose control of the annular rubber belt and its load, although the correct selection of motor and control device can avoid the accidental fault, but we need to use the brake, in order to power and emergency stop plays a role of emergency braking;