CSR65 metallurgical coke

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

We export many kinds of coke, such as CSR64 % and CSR 62 metallurgicalcoke (met coke), the NUT coke of 20 to 50 mm, coke breeze of 3 to 6 mm, and so on.

We can offer belowgrade met coke, origin from China.

Quality (Specificationsguaranteed at Load Port):

Ash                           12.5%Maximum (on dry basis)

Volatile Matters                 1.5%Maximum (on dry basis)

Sulphur                        0.65%Maximum (on dry basis)

Phosphorous                    0.035% Maximum (on dry basis)

Micum 10                      8.0% Maximum

Micum 40                      82.0% Minimum

CSR (ASTM Standard)           65.0% Minimum

CRI (ASTM Standard)           28.0% Maximum

Size 30-90mm                  90.0% Minimum

Under 30mm                5.0%Maximum

Over 90mm                 5.0% Maximum


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Coke boiler belongs to coal-fired boiler
They produce coke boiler to clean fuel production to reduce emissions as the main content.
Q:What are the criteria for coke classification and how to distinguish between primary and two grade coke?
Quality index of cokeCoke is the solid product of high temperature carbonization, the main ingredient is carbon, is the pore structure has a crack and irregular (or pore porous). The crack number directly affects the coke strength and crushing strength, the index generally refers to the unit volume of the crack (crack number within the coke grain length). To measure the pore structure of the main indicators to measure with porosity (only coke pore volume accounted for percentage of the total volume) that it affects the coke reactivity and strength. The different uses of the coke porosity index for different requirements, the general metallurgical coke gas hole rate in 40 ~ 45%, foundry requirements in 35 ~ 40%, coke export requirements in 30%. Coke crack degree and the porosity level, and the coking coal has a direct relationship, such as coal based coke refining, crack, high porosity, low strength and coking coal as a base; Coke coal refining. Crack less, low porosity and high strength. The strength of coke is used to denote the crushing strength and abrasion resistance of two indicators. The coke crushing strength is that coke can resist foreign impact force without ability along cracks or defects at the broken table, shown by M40 wear; strength of coke coke refers to the ability to resist external friction without surface of glass forming debris or powder, by the M10 value. The effect of the crack of coke crushing strength, M40 value, M10 value and abrasion strength influence of coke pore structure. M40 and M10 were determined by lot. In China the migon drum test in Germany.
Q:What is the amount of waste gas produced by a ton of coke burning
Metallurgical coke with high carbon content, high porosity, high strength (especially high temperature strength), is an important fuel and reducing agent of blast furnace ironmaking, but also the entire blast furnace pillar supporting agent and loose agent
Q:Effect of coal fineness on coke
In coking, the caking property is not good and the coke quality is reduced. Therefore, from the perspective of the uniformity of coal, coal fineness of some good. From the operation point of view, the greater the fineness of coal coal bulk density is lower, the production capacity of coke oven is low, into the coke oven, fine coal powder easily by gas is brought out, and easy blockage of ascending pipe, gas collector, affect the normal production of the coke oven, and the set of tar in the trachea increased, the effect of recovery operation. Therefore, from the production point of view, the fineness of coal should not be too large. Bulk coal in the top of the coke oven, coal crushing fineness of the general control in less than 3mm component in the range of 73~83%. Tamping coking, generally about 90%. In this range, the fineness of pulverized coal can meet the requirements of coke quality and coke oven operation. The small coal crushing will reduce the adhesion and the bulk density of coal, so as to reduce the coke quality.
Q:China's coke iron smelting began in what time?
The ancient iron smelting method in smelting iron block, lower temperature, iron ore solid reduction sponge iron, and iron into play by forging. Smelting iron block, furnace, furnace with ground and shaft 3. The block iron making in our country began in the spring and Autumn period, and in the near future, the pig iron with more than 2% carbon dioxide was refined and used as a casting tool
Q:How many degrees of coke ignition temperature can ignite coke
Ignition temperature (450-650) in air;The main physical properties of coke are as follows:True density is 1.8-1.95g/cm3;Apparent density of 0.88-1.08g/ cm3;
Q:Who can talk about the coke industry prospects?
Steelmaking is definitely not coke, but now most of the very mature iron making technology needs coke, the future direction of development of iron is not used or less coke
Q:Coke coal charcoal are used for what
Charcoal:1 metallurgical industryIn the past, the charcoal was used to smelt iron ore, and the pig iron was melted by charcoal and coke. The structure and mechanical properties were not the same even if the chemical composition was the same. The charcoal smelting pig iron generally has the fine grain structure, the casting is compact, does not have the crack the characteristic, the pig iron with the charcoal production contains the impurity is few, is suitable for the production high quality steel. Due to the reduction of charcoal, so in the metallurgical industry can be used to restore ore smelting metal.In the non-ferrous metal production, charcoal used for surface flux, non-ferrous metal melting, the surface flux in the molten metal surface protective layer, so that the separation of metals and gases, can reduce the loss of molten metal splash, and can reduce the melting material in gas saturation.A large amount of charcoal is also used to produce crystalline silicon, silicon used charcoal ash production should not contain too much carbon and head.
Q:What is the difference between coking coal and coke
Coking coal is an essential raw material for the production of coking coal, coking coal is one of the main uses of coke, coke is full of coking coal, coking coal is necessary for coke.
Q:The pulverized coal is separated from the air to enhance the heat, in addition to the main coke
Ethylene containing carbon carbon double bond can add poly to generate polyvinyl chloride, can be used for food packaging, reaction equation is: nCH2=CH2Initiator,The answer is: nCH2=CH2Initiator;

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range