Butterfly Valve DN350 Turbine Type BS Standard Hand Wheel

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
50 pc
Supply Capability:
5000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

1. Manual Wafer Butterfly Valve Description

A butterfly valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. Operation is similar to that of a ball valve, which allows for quick shut off. Butterfly valves are generally favored because they are lower in cost to other valve designs as well as being lighter in weight, meaning less support is required. The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.

 

2.Main Features of the Manual Wafer Butterfly Valve 

a)Cast hole. Flange connection meet ANSI 125/150#   DIN PN10/16   BS4504 PN10/16 in the meanwhile.

 

b)Soft seat. Replaceable. Increase of service life.

 

c)Double half shaft without pin.

 

d) Square and short neck. Easy to stick scutcheon and cost saving.

 

3. Manual Wafer Butterfly Valve Images

 

Butterfly Valve DN350 Turbine Type BS Standard Hand Wheel

Butterfly Valve DN350 Turbine Type BS Standard Hand Wheel


4.Manual Wafer Butterfly Valve  Specification

 Butterfly Valve DN350 Turbine Type BS Standard Hand Wheel

5.FAQ

 

1. What is manual wafer butterfly valve?

A: Wafer style is the more common of the two and is less expensive than the lug style. The wafer style butterfly valve is just about the standard. It ís so common that no one even bothers to use the word "wafer" when ordering a butterfly valve. It is taken for granted that if a butterfly valve is ordered, a wafer style will be received.

 

2. How about the Installation of the Wafer Style Butterfly Valve?
A: Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.

 

3. What is the working principle of manual wafer butterfly valve?

 A: A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "butterfly" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Can the inlet and outlet of butterfly valve be reversed? Why? What will happen if the reverse gear is installed?
Are butterfly valves and check valves fitted together?Butterfly valve is nothing positive and negative ah!
Q:Three eccentric hard sealing butterfly valve, why not fit in the end of the pipe?
The sealing ring will hold up. It does not fit in with the flange end of the pipeline, this addition is the most common and convenient pipeline after purge and easily add pipeline.
Q:The difference between the electric control valve and the electric butterfly valve, respectively, the application situation
Butterfly valve switching speed, fluid resistance is small, but the flow control is not good, suitable for only fast opening and closing occasions. Control valve switching speed is relatively slow, fluid resistance, but the flow control of the linear good, suitable for flow control requirements of the occasion.
Q:That industry uses most of the butterfly valve, and only use the butterfly valve, a large number of use of butterfly valve, seek expert advice!
Large diameter heating pipes with more than butterfly valves, greater than or equal to DN600 are used butterfly valve
Q:What are the torque specs for a 1994 Mazda 929 valve cover?
you do not torque valve covers down, buy a new gasket , I would get a good quality rubber one and some blue rtv sealer, clean any crap off the valve cover no glue no bits of gasket nothing, same thing on the head surface, glue the gasket on the valve cover, let it set, then carefully put it on, start with the bolts in the middle and work out finger tight all of them, then just snug the bolts down, dont crush the gasket, you can also use a light duty locktite to hold them in place, and often times old valve covers are warped, it is too your advantage to make sure its as flat as you can get it, or spend a few bucks a buy a new one. your choice, but snug the nuts down good with out crushing and bending the thin sheet metal of the valve cover.
Q:What does "C" in D971F-16C DN450 RF mean for electric butterfly valves?
Valve carbon steel -16c body 316 stainless steel -16r
Q:How does PLC control butterfly valves?
PLC output signal, access to the butterfly valve actuator or locator, you can control
Q:toyota mechanic valve adj 1.8l?
valve adjustment . you need to know the fire order. the gage between the stem. rotators the cranshaft. it could be cold start. cylinder need to be bottomed center.
Q:Why use special flanges for butterfly valves?
Because to use special flange butterfly valve butterfly flange diameter is just the butterfly inside diameter of DN coincides with a slot in the back, and this is the connection of the steel pipe is inserted into the slot, so as to ensure the sealing effect, but with a flange piece of ordinary cannot guarantee the effective sealing effect.Butterfly valve plate installed in the direction of the diameter of the pipe. Butterfly valve structure is simple, small size, light weight. Consists of only a few components. The utility model can be rapidly opened and closed only by rotating 90 DEG, the operation is simple, and the valve has good fluid control characteristics. When the butterfly valve is in the fully open position, the butterfly plate thickness is the only resistance when the medium passes through the valve body, so the pressure drop produced by the valve is very small, so the flow control characteristic is better.If the butterfly valve is used as a flow control, the main thing is to correctly select the size and type of valve. Butterfly valve structure and principle, especially suitable for making large-diameter valves. There are two kinds of butterfly valves commonly used: clip type butterfly valve and flanged butterfly valve. The clip type butterfly valve is a double headed bolt connecting the valve between the two pipe flanges. The flange type butterfly valve is provided with a flange on the valve, and a bolt is used to connect the flanges at the ends of the valve to the pipe flange.
Q:Butterfly valve is generally used in what position?
It can also be used for switch control of low pressure pipeline medium.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range