Butterfly Valve DN150 Wafer Double Eccentric
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 500 set
- Supply Capability:
- 5000 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1.Manual Wafer Butterfly Valve Description：
A butterfly valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. Operation is similar to that of a ball valve, which allows for quick shut off. Butterfly valves are generally favored because they are lower in cost to other valve designs as well as being lighter in weight, meaning less support is required. The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve.
2.Main Features of the Manual Wafer Butterfly Valve
1)Small in size and light in weight and maintaince.It can be mounted whereever needed.
2)Simple, compact structure, quick 90 degree on-off operation.
3)Disc has two-way bearing, perfect seal, without leakage under the pressure test.
4)Flow curve tending to straight-line. Excellent regulation performance.
5)Various kinds of materials, applicable to different medium.
3. Manual Wafer Butterfly Valve Images：
4.Manual Wafer Butterfly Valve Specification：
Size | DN40-DN1200 |
End flange | ANSI B 16.1, EN 1092, AS 2129 |
Face to face | ANSI B 16.10; EN 558-1 Series 20 |
Top flange | ISO 5211 |
Normal Pressure | DN40-DN600 PN1.0/1.6MPa (150/200PSI) DN700-DN1200 PN1.0MPa (150PSI)
|
Body | CI/DI/WCB/ALB/CF8/CF8M
|
Seat | NR/Hypalon/EPDM/Neoprene/NBR/Wear-Resistant EPDM/Viton/Silicon/Heat-Resistant EPDM/White NBR/White EPDM/EPDM (NSF)/PTFE |
Suitable Temperature | -40c~80c
|
Apply | Fresh water, sewage, sea water, air, vapor, food, medicine, oils, alkalis, salt etc. |
5.FAQ
1. How about the Installation of the Wafer Style Butterfly Valve?Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.
2. What is the working principle of manual wafer butterfly valve?
A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "butterfly" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.
- Q:What is the difference between wafer (flangeless) type and LUG type of butterfly valves?
- WAFER butterfly valve is the valve is divided into LUG (ears) with and without LUG, ordinary LUG without clip on 12 points in the direction of valve is generally two to four bolt holes was not, whereas the LUG of butterfly valve cross dispersed in a circle. Bolt hole. With LUG all bolted through the LUG, so that the butterfly valve and the clamp on the two flange connection is more solid, you check the valve picture, it is easy to understand
- Q:I was wondering if someone could tell me the manufacturing date on this aircraft engine valve.
- Wow Hannah! That's a cool find for sure! It appears to be possibly a valve for a radial aircraft engine as it looks very similar to ones i've seen used in Pratt+Whitney R3350's etc. It looks like it could probably date to the 1940's up thru the 1950's. Look for a Part Number stamped on the valve or on the box. After WW2 there were all kinds of manufacturers making parts for airplanes. Many were gobbled up by competitors, converted to manufacturing other products or went out of business altogether. However, a few did hang on....and I think this may be what has become of Thompson Aircraft today.... Thompson Aerospace, Inc 22431 Antonio Parkway B160-102 Rcho Sta Marg, CA 92688-2804
- Q:Buried extension butterfly valve is buried or need to repair the valve well, can build the valve well, the extension rod butterfly valve installed in the valve well, the extension rod to avoid covers, the top of the valve well out, so that the hand wheel in the ground operation.Atlas S143 is less than the inner diameter of DN150 valve wells only 1200mm, DN200-DN250D diameter of only 1400mm, 700mm valve covers, valve rod and a handwheel to lengthen through the valve cover, valve wells is built to cover the embedded pipe or tube? Is there a standard atlas?
- The establishment of a repair valve well, easy to repair, usually hydrogen long rod butterfly valve installed in the well. But if the quality of buying long stem butterfly valve, it can also be buried directly, not easy to bad
- Q:How do i use a valve spring compressor. It looks like a c-clamp, so don't tell me how to use a smaller one, but the bigger one.Thanks
- The forked end goes over the valve retainer, the flat end with the screw goes against the valve face. Simply close the handle to compress the spring. You may need to adjust the width of the jaws to fit the retainer and adjust the length of the screw to compress the spring the right amount. Sometimes it helps to gently tap the edge of the retainer with a hammer to loosen the keepers before compressing the spring.
- Q:I did a compression check on my 350 chevy. I have low compression of 175psi on one cylinder.The other seven cylinders range from 195psi to 205psi Could the valves be too tight on the cylinder with 175 psi compression?
- Chev engines have hydraulic lifters, keeping the valves adjusted correctly at all times. 20 lbs isn't much to worry about anyway, but if you want dump a little oil (about a tablespoons worth) into that cylinder and recheck it. If the compression jumps up, then your rings are getting weak. If not, you may have a leaky valve.
- Q:The difference between the electric control valve and the electric butterfly valve, respectively, the application situation
- Butterfly valve switching speed, fluid resistance is small, but the flow control is not good, suitable for only fast opening and closing occasions. Control valve switching speed is relatively slow, fluid resistance, but the flow control of the linear good, suitable for flow control requirements of the occasion.
- Q:My caravan is a bit sluggish on the pick up, I replaced the wires/plugs and the electronic distributor(I think thats what it is..). still a bit sluggish. Should i look at the valve gasket? Or fuel filter, or fuel pump next? 03 caravan sport 3.3L
- the valve pan gasket won,t cause it but the fuel filter will if it,s starting to clog up and also the cat nverter !
- Q:My quot;check engine soonquot; light came on yesterday and soon after that I took it to the nearest Midas to have the diagnostic test run on it - they stated I needed an ERG valve. I have no clue what it is and was told that it could run $160. - $300. for my 1900 Astro van. what is an ERG valve? I have noticed that my van has a low humming sound when I'm driving it.
- The EGR valve is there to reduce nitrous oxide emissions and lower the temp of the combustion charge. This has the affect of reducing the octane requirement of the engine. This isn't a bad thing. When the valve hangs open, the thing will run bad at idle and could even die. The thing is, the valve could be perfectly fine and the sensor could be bad. Since some states won't give you a sticker if the light is on, you're probably stuck with replacement.
- Q:What's the size of the signal butterfly valve sleeve?
- The signal valve of the fire door (not in the signal valve shutter doors, fire signal valve use: top fire signal butterfly valve with the valve opening and closing signal device, when the valve is closed by 25% (open degree 4/1), the signal device output signal was mistakenly closed to the fire control center. Therefore, this butterfly valve is the best matching product of automatic fire sprinkler system.
- Q:16 inches below the choice of electromagnetic valve can be the same, it turned out to be DN200 election 1/4, and now there are DN350 can also use this? With it, limiter, pressure relief valve, locator model will change?
- DN200 pick 1/4DN350, DN400 corresponding solenoid valve, you can choose 3/8 hose 12mmOther accessories are related to valve path and pressure. If the same series, the valve has no change at all.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
Butterfly Valve DN150 Wafer Double Eccentric
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 500 set
- Supply Capability:
- 5000 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
