BS5163 DCI Non-rising Gate Valve with pass type
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specifications
1.General design:DIN,BS,ANSI
2.Rising or Non-rising stem
3.Solid wedge disc
4.Clockwise closing direction
5.Bolt bonnet
Product Name:
gate valve
Technical Data
DN40-DN2000mm
Body: Cast Iron, Ductile Iron
Stem: Stainless Steel,Brass
Disc: Ductile Iron
Flange Connection:EN1092-2 PN10/PN16/PN25,
ANSI B16.1
BS10 Table D/E,JIS10K/16K
Standard:DIN3352-F4/F5,BS5163,BS5150,BS3464,ANSI
Product Features
Bolt Bonnet
Replaceable O-ring
Low torque operation
Outside screw and yoke
Clockwise closing direction
Graphite packing
Seat rings are pressed into wedge and body.
- Q:My faucet is too high in my toilets, how to do it?
- You can buy a filter to replace the bubble up, when the water and air fully mixed, not only water also reduces the water flow speed, play a splash effect. General specifications are basically the same, but there are different situations, hardware bathroom or online are.
- Q:How to install the basin faucet
- Basin basin of the basic information, teach you how to buy a good basin faucet, how to mix with the basin faucet and how to maintain the clean basin faucet, and basin faucet according to the installation method is divided into: wall faucet and sitting faucet.
- Q:Is the basin faucet to the angle valve?
- Hot and cold water, then two angle valve, a single cold on a corner valve. To install the angle valve, then buy a good point, do not lead no bad, angle valve first bad, it would be better not installed.
- Q:How to self - study at home cappuccino
- Now Nestle coffee out of the "cappuccino that is red coffee", usually in the supermarket can buy, I bought, red factory muscle class can be straight on the trip after the snow leopard shot out there will be a layer of cappuccino foam.
- Q:I just wanted to replace my kitchen sink but now that we have it in my cold water hose wont fit into the cold water valve.. they are both female ends. is there an adaptor i can use? do i have to replace the valve with a valve that has the right connection? and lastly what are these parts all called so i wont look like an idiot at the hardware store. thatnks for the help every one!
- Well, the first thing the hardware person is gonna ask is "What kind of plumbing do you have?" (Copper, plastic, iron?) If the two female ends you have are of the same type (1/2" NPT, for example -- NPT standing for National Pipe Thread, and the 1/2" referring to the "nominal" inside diameter of the pipe, which is actually considerably larger), then it's a simple fix: Get a short 1/2" galvanized iron "nipple" (which, despite its name, has two threaded male ends), and that should go between the two female connectors and solve the problem. If the threads don't match on one side or the other, you'll need an adapter, which the hardware store can provide. If your valve is functional, you shouldn't have to replace it. Be sure to use teflon tape on the threads: As you're facing one of the male ends, tightly wrap a strip of the tape clockwise two full laps around the threads. (By wrapping it clockwise, the twisting of the female fitting onto it won't undo the tape.) The teflon tape not only fills any flaws in the metal surfaces; it also lubricates the joint so you can get it good and tight. PVC plastic pipe generally has NPT fittings for attaching fixtures; copper might have the same, or have "flare" or "compression" connections. Galvanized iron pipe always is fitted with NPT threads, and 1/2" is most common for kitchen and bathroom. PS: I just now saw your photos, which weren't yet posted when I started writing this. The pictures are too small for me to be sure what you have there, but maybe the problem is just that you have two connector tubes! Take one of 'em off at the other end, and attach the free end of the other one there. In selecting which one to detach, the one coming from the plumbing is probably far easier to access; the one going up to the faucet would require a basin wrench -- not a fun tool to use -- and a flashlight, and three hands! Congratulations on doing it yourself!
- Q:Anwar how is it?
- is acceptable,
- Q:The bathroom put a washing machine, bought a three-way dual-switch faucet, had wanted to install in the basin to connect the faucet on the angle of the valve, the result because the bathroom cabinet
- For health and safety! It is recommended to go to the supermarket to buy blue clean water block, the water tank will be sterilization and automatic flushing toilet and water tank
- Q:How the basin basin faucet and the water is said to be more detailed yo
- Generally use S-tube, the size of easy to use 50mm (diameter) PVC pipe, the same room smear glue. In the mouth of the outlet basin under the outlet with a hose connection, to paste firmly
- Q:Faucet to open the water heater why not fire
- But the kitchen from the electric water heater pipe long water pressure is small, the beginning of the water fretting did not open, there is also a kitchen faucet out of the hot water there is a clogging of the dredging cut off cut the dregs of dengling japonica down to the small amount of water, See the hot water pipe to remove the hot water faucet
- Q:Domestic bathroom basin hot and cold faucet better brand
- Stainless steel faucet does not require plating, is a manual or mechanical polishing, it should be environmentally friendly, and now the domestic electroplating plants are polluting large, for future generations, I suggest that we still use stainless steel faucet good, although a large consumption of investment , But should not be in the future because of plating off and then re-purchase.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
BS5163 DCI Non-rising Gate Valve with pass type
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products