EPR Insulated (low一smoke halogen-free flame一retardent) Shipboard Power Cables
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 m
- Supply Capability:
- 100000 m/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Product characteristics and application
These cable are interded conrtol system or shipboard and off-shore building.
Executive Standards
IEC60092一353, IEC60332一1、IEC60332一3(A)(Category A)、IEC60331、IEC61034、IEC60754
Construction of Cable
Type and names
Type | Name | No.of cores | Nominal cross-sectional area |
CEF/DA/SA | EPA insulated CR sheathed shipboard power cable, type DA/SA | 1~5 | 1.0~150mm² |
CEF80/DA/SA | EPR insulated CR inner sheathed bare tinned copper wire braided shipboard power cable,type DA/SA | ||
CEF82/DA/SA | ERR insulated CR inner sheathed tinned copper wire braided PVC outer sheathed shipboard power cable, type DA/SA | ||
CEF90/DA/SA | EPR insulated CR inner sheathed galvanized steel wire braided shipboard power cable,type DA/SA | ||
CEF92/DA/SA | EPR insulated CR inner sheathed galvanized steel wire braided PVC outer sheathed shipboard power cable, type DA/SA | ||
CEV/DA/SA | EPR insulated PVC sheathed shipboard power cable, type DA/SA | ||
CEV80/DA/SA | EPR insulated PVC inner sheathed tinned copper wire braided shipboard power cable,type DA/SA | ||
CEV82/DA/SA | EPR insulated PVC inner sheathed tinned copper wire braided PVC outer sheathed shipboard power cable, type DA/SA | ||
CEV90/DA/SA | EPR insulated PVC inner sheathed galvanized steel wire braided shipboard power cable,type DA/SA | ||
CEV92/DA/SA | EPR insulated PVC inner sheathed galvanized steel wire braided PVC outer sheathed shipboard power cable, type DA/SA | ||
CEH/DA/SA | EPR insulated CSM sheathed shipboard power cable, type DA/SA | ||
CEH80/DA/SA | EPR insulated CSM inner sheathed tinned copper shipboard power cable, type DA/SA | ||
CEH82/DA/SA | EPR insulated CSM inner sheathed tinned copper wier braided PVC outer sheathed shipboard power cable, type DA/SA | ||
CEH90/DA/SA | EPR insulated CSM inner sheathed galvanized steel wire braided tinned shipboard power cable, type DA/SA | ||
CEH92/DA/SA | EPR insulated CSM inner sheathed galvanized steel wire braided PVC outer sheathed shipboard power cable, type DA/SA | ||
CEPF(J)/SC | EPR insulated PO sheathed low-smoke halogen-free flame-retardant shipboard power cable. type SC | ||
CEPF(J)80/SC | EPR insulated PO inner sheathed tinner copper wire braided low-smoke halogen-free flame-retardant shipboard power cable, type SC | ||
CEPF(J)86/SC | EPR insulated PO inner sheathed tinned copper PO outer sheathed low-smoke halogen-free power cable, type SC | ||
CEPF(J)90/SC | EPR insulated PO inner galvanized steel wire braided low-smoke halogen-free shipoard power cable, type SC | ||
CEPF(J)96/SC | EPR insulated PO inner sheathed galvanized steel wire braided PO outer sheathed low-smoke halogen-free shipboard power cable, type SC | ||
CEPFR(J)/SC | EPR insulated polyolefine sheathed flexible flame-retardant shipboard power cable, type SC |
- Q:trying to install garbage disposal and need it powered.I wanted to use this computer cable because the one that was with disposal got damaged.I would like to know how to determine which of the three (brown, blue, yellow) wires is ground. And for other two does it matter which way they are connected?Thanks in advance.
- STEP AWAY from the appliance. A computer draws a lot less than that motor you propose to connect. Don't be cheap. Get the proper size cord. What you show from the computer looks like #20. You want a 3 W. #16, cord.
- Q:I'm trying to plan out my new install and I'm debating whether or not to spend money on power cable adapters and run o gauge to a distribution block thats 0g in and 4g out, therefore running a 0 to 4g cable adapter inbetween every terminal on the distribution block --or-- to Instead run 0 to the distribution block and 4 from the block to everything. I have a 1200RMS sub amp and a 200RMS 4-Channel amp. Hi output alternator. Big 3. So if anyone can give me some advice on whether or not they're worth the money that would be awesome. Oh and my amps accept 4 gauge.
- back interior the day while audio electronics grew to become into evolving from monophonic sound to stereophonic sound, manufacturers of stereo audio electronics unique the left channel enter for monophonic sound (in case you purely had one enter) and, if there grew to become into no longer something plugged into the final enter jack, the monophonic sound grew to become into dispensed to the two left and precise inputs. on the grounds that mono is fantastically uncommon at present, i don't be attentive to if this remains accepted on stereo inputs (alongside with powered subwoofers), yet you're able to attempt it. If it relatively is no longer the case (plugging it into the left enter purely is going interior the direction of the left amplifier), no remember in case you chop up the sign or no longer is in fact a wash. A subwoofer has 2 voice coils on the motive force, one powered by making use of the left enter and the different powered by making use of the final enter. in case you purely have, say, the left enter plugged in, you're purely using the subwoofer with the left amplifier and voice coil. in case you chop up it, you're actually using the two voice coils. yet, the chop up itself cuts the sign point in 0.5. So, you have 0.5 as plenty sign enter to each amplifier and the output quantity of the subwoofer is not any diverse than purely plugging in one enter. one factor you need to do is to get a small, affordable stereo amp or receiver, plug the LFE output into one enter, set the amplifier mode to mono, and run the two line outputs to the subwoofer. that should offer you 2 finished line point inputs to the subwoofer from the single LFE cable.
- Q:NO power convertor needed? I can go straight from AT to ATX?
- You are confused between AT and ATX. As described by pdl756 the power connections are different and two plugs. Another big difference was the AC went from the PSU to the Start switch on the P.C case and back to the PSU for switch on. AXT started with a 20 pin power plug and later to a 24 pin power plug. Your link shows that converter from 20 to 24 pin but it was not needed for long because PSU manufacturers provided a 20 plug plus a 4 pin clamp on extension
- Q:What are the causes of the power cable fire accident? How to prevent
- DIY notebook, I recommend you look at the Jingdong Mall, where there are genuine hardware and equipment, that is just the same as the same to buy back, you have to go home to assemble it! Such as CPU, graphics cards, hard drives, processors, heat sinks, monitors and the like can be bought
- Q:For example i have the Pelican xbox 360 av and power cables not the microsoft kind. So as i heard does it make a difference like does the intercooler still eventually melt in to your xbox 360 or will it stay normal? I ask this question because my niece also has an xbox 360 and while my 360 was getting repaired i came over to play her 360, when i plug in the intercooler it worked fine but i had a little trouble pulling the power brick cord out of the intercooler and hers is microsoft av and power cables, but when i pull my Pelican power brick cable out of my intercooler it came out easily, no trouble at all. So thats why i wanted to ask the question.
- its not going to melt your xbox 360. its why they made it to cool down the system. if someone told u it will is stupid.
- Q:Electrical equipment installation project "power cable laying" cable cross-sectional area refers to the cable cross-sectional area, or refers to the copper core cross-sectional area, such as 3 × 25mm2 refers to 25mm. 75mm2 or cable cross-sectional area of 490mm2? More
- Said cross-linked polyethylene insulation, double steel armor, PVC outer jacket. Voltage level 0.6 to 1 kV, 5 core, cross section 10 square millimeters. About four centimeters in diameter.
- Q:I am trying to install a new Power Supply Dynex 520 Watt ATX and I cannot figure out what cable to connect to the hard drive. It was very small and I had a hard time connecting it. Do you have a clue?
- besides the actuality that maximum power aspects are interchangable, no longer all power aspects artwork on all structures. some issues to make valuable of while procuring a power furnish are one million. the recent furnish has the superb power pins could desire to connect on your motherboard and instruments. 2. the recent power furnish suits on your computing gadget case, the dissimilar severe end power aspects are somewhat extra desirable and don't sit down real in all circumstances, 3. the recent power furnish has the two sufficient Wattage and Amperage. a superb style of individuals make the blunders via getting getting a power furnish with too low amp score by way of fact it became into extra inexpensive. look at the two by way of fact they're the two important.
- Q:My old card only needed one of these cables. but my new 4870 will need two. can i just use a IDE-to-PCI-e power cable? its only got 3 wires out of the 6 though. does this matter?
- You okorder /... It takes two 4-pin PSU molex connectors and converts it into 1 6-pin PCIe connector. Make sure your PSU can supply the necessary amps on its +12V rails, and if you got a PSU with multiple +12V rails, you need to make sure you got the load spread out among different rails to avoid overloading one rail.
- Q:Welding cable (230v) doesn't, so why would (14v) car audio cables
- Voltage is not your main enemy when dealing with electricity. It's current or amps that are the main concern. You can think of it like a water hose, the V is the speed of the water, the A is the amount. Take Ohm's law for example. Say we have an amp that's producing 1000W With a 230V power system we have 4.3A, with a 14V power system we have 71A. That's a lot of amperage. Car power cables have a thick jacket to prevent shorts, shorts are bad. If you had a large cable going from one end of your car to the other, without a fuse. (lot's of people don't fuse correctly) If that cable comes in contact with the metal of the car it's going to short and that whole cable is going to get red hot and burn your car to the ground.
- Q:How would I go about stripping 4 gauge power battery cable for my amp? oh and how would i screw the fuse holder down? with what kind of screws? thank you!
- I use a knife to strip that wire, just be careful not to nick the wire. Drill a hole and use sheet metal screws to screw the fuse holder down.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
EPR Insulated (low一smoke halogen-free flame一retardent) Shipboard Power Cables
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 m
- Supply Capability:
- 100000 m/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords
