Q:To save on precious water, time and money

The usual way for the washing machine to rinse the clothes after they have been washed is for it to refill up with clean water and slosh the clothes about for a while before draining out the water. Spray rinse is a method where after the clothes have been washed fresh water is sprayed on them as they are tumbled about , this uses less water.

Q:Electronics Tourism Fashion Machinery

Producing anti-americans. We saved them from WW1. We saved them from WW2, and if and when WW3 comes about, they can go to hell.

Q:What is defined in construction engineering as large machinery?

The specific check check, there are Jixietaiban size division principle in great detail. Construction machinery should be unified in the following twelve categories

Q:What is a mechanical mouse?

The other is the photoelectric mouse, which is visible everywhere in the market. The photoelectric mouse operates mainly through three functional modules.

Q:What are it's advantages and disadvantages in both commercial farming and subsistence farming?

Good question Advantages of Commercial Farming Can generate cash, the products are therefore intended to be marketed for profit. An extra profit is needed to fund the next cropping activities. A positive impact on an economy, unemployment decreases more people and resources are fully utilize and as a result government generates more revenue through taxes which makes an economy of a country more powerful. Disadvantages of Commercial Farming is that only certain crops would be produce as it has more money value. Peoples' would not get a variety to choose. Advantages of Subsistence Farming The people who worked there can get the food and it is a quite cheap as compare to Commercial Farming where excess of money is required to operate the farm whereas in subsistence farming you just have to buy a little piece of land and little money to be spend on the crops. Disadvantages are there is no proper source of income in this farming system. Difficult to buy seeds for new crops due to a cash-flow problem. A farmer has to work hard to yields the crops. Hope this helps and I think you are a student, if is it so then I am sure with this answer you would get 100% :)

Q:Me and my friend installed a 64-bit OS on his 32-bit machinery that's bought in 2004 it's a athlon xp 2.8GHZ and 2.0GB ram and it works preety fine execpt that it's very slow at times and it's very incompatable. Can we actually do that becasue when we were installing it it just warned us that oyur processor is not 64-bit capable do still want to procced we clicked yes and it worked fine. honestly this is not a lie I am telling the truth.

It is possible, but why would you do it? They give you different Processer Architectures for a reason

Q:why are damping devices often used on machinery?

to kill vibration

Q:sorry if that not a correct question but that the question i need for my essay

The basics of a nuclear power station are: The nuclear reactor, comprising of: - The fuel cell (Uranium / Plutonium) - The control rods (keep reaction rate at critical level) -Moderators (For uranium, they slow down the neutrons, and so keep the reaction going) - Some form of coolant You also need a heat exchanger system, this may be done through direct heating of the water by the reactor (if it as used as a coolant) or through heating of the water by use of CO2 gas This then heats water, which turns a turbine. To keep the reaction safe, there will also be a lot of control machinery, with automated shut-down systems, and programmed containement procedures

Q:For example, what programming language and/or software would be used to control an automated sprinkler system, or other automated device? I want to know how the software interacts with the machine.

Usually industrial computers us logic programming. A PLC, ie, Progrmmable Logic Controller, is used in many automation uses. They use logic to make decisions.

Q:these machines all weigh in the hundreds and are up to my waistthere used but in good conditionthey are:JOINT PLANER(oh and is there a better name for this one?)TABLE SAWSURFACE PLANERi want to know how much these items would cost?im trying to sell them but not sure what the prices should beim planning to put em on ebay and would appreciate your helpthank you!

Around here there is limited demand for it. Scrap prices mostly. Sad, but not too many people can use it and often it's 3 phase and requires an industrial area to set up. Newer shops don't want to fuss with tuning and repairing it and are more likely to go with CNC units or multi-function European machines. There are a few people that like the old iron Around here it would be called a jointer and thickness planer.