Q:Just moved into a new house and the basement is already wired for surround sound. The ends are two wires one silver one gold/brass wrapped together with plastic. Looks like they were cut at the ends. How difficult would it be to wore the speakers myself?

The color coded wire will correspond to the connection of the positive and negative. You would connect the wire to the receiver, depending on the location of the speaker. Check the speaker that is already installed and see what color wire is going to what terminal on the speaker and match that connection to your receiver. Front speaker connected to the front speaker terminal of the receiver. Your receiver owners manual will also provide you with some direction. Hope this will help you out.

Q:If you put clay over wire and bake it would the wire melt and ruin the sculpture?Details on wire:I'm not sure what kind of wire it is but it says Bright Floral Wire..Wire is silverDetails on Clay:Again, im not sure what clay...its from polyform products and it says Premo Sculpey so im guessing Polymer? :#92;Clay is Black.Bakes for 275F (130C)30 minutes per/par/por1/4 in (6mm)

(Premo okorder /

Q:i bought a programmable thermostat, and the wiring i see doesn't make any sense. it's for central air, heating and cooling. there are no tags or labels on the wires, and it was probably installed in the seventies.there are four wires coming out of the wall, and they're screwed into four of six slots:Y = blue wireG = red wireW = green wireR = white wireB = emptyO = emptythe new thermostat has the following slots: G, Rc, Rh, Y/O, W/B, Y1. how should the old labels correspond to the new ones?

First of all from what you are saying on how the old thermostat is wired,your furnace is wired up wrong...On the old thermostat the red wire should go to R... The white wire should go to W... The green wire should go to G... And the blue wire should go to Y... On the new thermostat the red wire should go to Rc and a jumper wire from Rc to Rh... The white wire goes to W/B... The green wire goes to G... and the blue wire goes to Y1... But if your sure that your old thermostat was wired the way you say it was then the red wire goes to G...the white wire goes to Rc with a jumper wire to Rh... the green wire goes to W/B... and the blue wire goes to Y1...

Q:When I am wiring my sub to my amp, what gauge of wire should I use? The sub is 750 rms and the amp is 700 rms. And how do I wire a 2 ohm sub DVC to a 2 ohm stable amp?

12 gauge wire would be plenty to wire subs to an amplifier. A 2 ohm DVC sub is not a good match for a 2 ohm stable amplifier. Your wiring options on a 2ohm DVC sub are 1ohm, and 4 ohms. You need either a 1 ohm stable amplifier or a dual 4 ohm DVC sub.

Q:I have a 98 RS Eclipse (420a) and i would like some opinions and recommendations for spark plug wires. Who makes the best or very good wires for my engine??

Buy the stock wires. Make sure there is no oil on the old wires or you will need to replace the valve cover gasket and the 4 plug tower seals that are inside the valve cover. The motor came with Champion plugs, don't use Bosch.

Q:Two long straight parallel wires are 12 cm apart. Wire A carries 2.5 A current. Wire B's current is 3.7 A in t?Two long straight parallel wires are 12 cm apart. Wire A carries 2.5 A current. Wire B's current is 3.7 A in the same direction.1) Determine the magnetic field magnitude due to wire A at the position of wire BB = ? T2) Determine the magnetic field due to wire B at the position of wire A.B = ? T3) Are these two magnetic fields equal and opposite? Why or why not?4) Determine the force on wire A due to wire B, and the force on wire B due to wire A.

(1) wire-A B = (uo)(I) / (2pi * r) B = (1.26E-6)(2.5) / (2pi * 0.12) B = 4.17E-6

Q:ok, so i love making jewelry, and probably a year ago i went to michael's bought a roll-type thing of really soft, really, really thin silvery wire. a couple of days ago i went to michael's again and it wasn't there.as i said, the wire that i had is very thin, very soft, and also after you bend it, it won't snap back- it actually will never go back to being completely straight, even if you try to make it do that.is memory wire what i should be looking for?does anyone have any suggestions to what kind of wire i should get?

Hi - I hope this information helps you - Beadalon? Remembrance? is thin, tempered stainless steel wire that is used as a beading medium. The wire is corrosion resistant and will resist tarnishing. Like a spring, Remembrance wire is rigid and snaps back to its original form when expanded and released. The wire remembers its shape and retains its coil form. Sterling Silver Wires To choose the right kind of silver wire for your project, you should know how you want the piece to look and what kind of piece you are creating. You will need to consider both the hardness of the wire and the gauge of the wire. There are three kinds of sterling silver wire. They are: Dead soft, half hard and full hard. Dead soft wire is very easy to bend. It can be better for wire wrapping or for making wire beads but will often not hold shapes intended for wire wrapping. Dead soft silver wire is usually used by people who work silver because it hardens as its shaped and hammered. Half hard sterling wire is stronger than dead soft but is still quite malleable. It is excellent in wire wrapping smaller or heavier beads and is a good choice for beading and jewelry making projects. Full hard silver wire is hard to use and bend and not necessarily recommended for jewelry making - at least for a hobbyist.

Q:I need thick floral wire and they keep saying things like 24 gauge 26 gauge 28 gauge.. like how would i know which one is thiickest if i'm buying it online.

For the best answers, search on this site https://shorturl.im/avRVF Hi Vanessa Diane, Floral wire can be bought at any local craft store ( Michaels etc ) and also your local WalMart. It does come in varying thicknesses. You will see on the outer packaging as the wire is numbered. Example, the lower the number the sturdier the higher the number thinner the wire. Happy DIY !

Q:ok so i have a power acoustik ov2-2200 amp right now and all my wires are working fine with this amp....i am going to buy a lanzar MXA282 which is more wattage (RMS)Do i need to get any new wires to hook this amp up? like the power ground or remote wires? thx... sorry for my ignorance :/

If you aare running with 4 gauge right now...your going to want to upgrade power and ground to 1/0 gauge. Your RCA should not have to be upgraded.

Q:The question is can i complete a ac circuit if i connect a live from one wire to a neutral from another.

It will conduct, it may also overload and melt the insulation on the wire without tripping a breaker. The purpose of a breaker is safety, one aspect is if a wire isn't large enough to carry the current applied it gets hot. If you have 15 amps from two breakers (on the same leg) the current on the neutral could be double the amount the wire is safe to carry, but the breakers won't sense a problem and may melt the insulation on the wire carrying 30 amps. There are a few instance that a neutral can legally be shared by multiple circuits, many restrictions apply, and conductors from separate romex cables do not satisfy any legal circumstance I can think of.