Q:how to wire a receptacle with 6 wires?

use 3 wire nuts and 3 jumpers, color to color and then connect the others together. Black wire to the dark screw, white color to the silver screw and the green to the ground connection. If this does not make sense to you contact a local qualified professional electrician to do the work.

Q:How are wired differ from wireless doorbells,next how are they installed and finally the cost of them?

Wired have a wire that connects the button near the door, the transformer, and the chime. When the button is pushed, the transformer energizes the chime, causing it to ring. You, or an electrician, must fish wires to a location where a transformer can get a constant supply of power, such as an outlet. There also need to be wires fished to the chime and the button. Wireless work with radio waves. Costs vary widely, depending on the setup you go with. Decent wireless units start around $35-40, and go up from there. New chimes for wired systems start around $8 and up. Transformers start at $10, buttons start around $5. Hope this helps.

Q:The black wire is called ground but what is the red wire called?

There are standards for wire colours but they vary between countries and industries. When I grew up in the UK black was used for negative power and red for positive power (e.g. ground and +12V). But trailer wiring in Canada seems to use black for +12V, for instance. In a digital electronic circuit, using silicon semiconductors, ground or 0V is often abbreviated GND and the +ve power supply as Vcc.

Q:I have a 2000 Mazda 626, and I am replacing the factory stereo with a Sony CDX-GT66UPW, I tried replacing it earlier and had to cut off the end plastic pieces for the original stereo wires and stripped the wires, So now I am trying to match up the wires from the new stereo with the old colors, But I don't know what color goes to what on the mazda? Can anyone give me a color coded diagram for the wiring?

In okorder /... There's a pretty good chance you'll need to replace a blown fuse in the vehicle's fuse box, too, especially if you cut all the wires together instead of one at a time.

Q:wire colors and funtions

Most Common Firing Order For Cars Is Plug 1, Plug 4, Plug 2, Plug 3 But Get A Haynes Manual And Check, I Dont Want To Blow Your Engine :)

Q:I just tore my old shed down, that was wired for electrical. though I never used power out there There is size 10 wiring (two wires), running from the house to where my shed was. I then bought a Tough Shed from The Home Depot and put it where my old shed was. While working on wiring my new shed for electricity, I turned power off to the entire house.I am trying to install power to the shed and I spliced the size 10 wires to size 14 (three cable, includes a ground) which I have connect to an electrical outlet in the shed, but once I turn the main power box back on, the circuit that runs power to the shed keeps tripping off. Am I missing something here?Thanks

Open the splices and leave the size 10 wires unattached with wire nuts over them. Try to power up the wires when they are disconnected. If it doesn't trip, you must have reversed your wiring. If it trips, the wires are shorted to ground. Perhaps the wires are rotted out under ground or grounded by a sharp metal edge. The shed curcuit breaker should be changed to a 15 amp if you will splice to 14 gauge. Or: There should be a breaker box like there was in the old shed, with 15 amp breakers for for 14 wire. 20 amp for # 12 wire.

Q:I have a kicker cvr 12 inch 2 ohm dual voice coil sub (400 watts) and a kicker zx750 amp. how to wire?

You okorder /

Q:I accidentally bought spark plug wires for a V6 2.7 liter engine and i own a 4 cyl 2.2 liter engine. are those wires interchangeable? i own a 95 Honda Accord

The wires the same except for the length, and the fact you have six and only need four. If you can find four that match the length of your old wires, they will work fine. You can also ask if the shop where you bought the wires will allow you to return the set you have and purchase the correct set. The set you need probably costs less than the one you have.

Q:the 2 wires that is connected from the key hole is cut .. how to fix or replace?

If there enough wire left on each side of the cut, say 1, then you could bear about 1/4 of the wire on each side and solder the wires back together making sure you are soldering the same wires together and wrap each soldered connection in electrical tape so they are not able to touch each other. Then a final wrap of tape around them both. If you are not up to soldering you could go to an auto parts shop and get a crimp connector to do the job, again bearing of wire is needed to get a contact through the cut area. If the cut is closer to the switch then there is no option but to replace the switch.....

Q:Hello, I couldnt find a more appropriate category for this question, so i'm hoping someone here knows a little about wiring. today my booster fan burnt out, so I had to replace it. I got a 6in-line duct fan from the home depot. When I got home and took it out of the box, there is just wires with no plug on it. I have an old lamp that I took the cord off of, but there is only 2 cords, pos neg. The new fan has 3. white, black, and green. the black is the hot wire, and the green is grounded to the metal of the fan, and the white I am not sure of. I just want to know how to wire this plug to this new fan. if anyone knows how to do this please get back to me. Any help will be greatly appreciated. once again thank you.

you recognize the strategies of ways a furnace works so i'm assuming you basically opt to comprehend if in-line followers artwork. i've got put in them to help heat up a single room and it raised the temperature some ranges which became sufficient for me. this would sound stupid yet in keeping with threat truly of putting in a 12 inch in-line fan to flow air in the process the main significant duct, you install a pair of smaller 6 inch followers in strategic rooms on your upstairs and it does no longer be as great so a techniques as static tension is worried. basically a concept, wish it helps.