Q:What is the difference between an anti-static floor and an anti-static floor?

1, the appearance of the edge of the anti-static flooring in the steel anti-static floor is more common, surrounded by a black conductive tape embedded in the protection of the bitter Huang Hong Puerong Guo bronze Gong expansion. And boundless anti-static flooring as the name suggests is no black strip around, after the installation of the floor between the joints more fine, the overall effect is better. 2, the installation of the edge of the anti-static floor because of the reasons for the black side of the installation of the ground on the flatness of the floor installation requirements are not too high. Unilateral anti-static floor because there is no black side of the ground, the flatness is poor or the installation is not in place are likely to lead to two pieces of the floor between the wrong seam, flatness of the poor situation, so the edge of the anti-static floor requirements for the ground leveling and workers to install the master The level of the requirements are higher than the side, the installation is difficult. 3, the latter part of the maintenance on the anti-static floor pavement is completed, in the latter part of the engine room line adjustment process, the need for special attention in the flip floor when the edge of the anti-static floor prone to edge of the situation, and no anti-static floor Black border also does not exist such a situation, but the boundless anti-static floor because there is no protection of the black side of the floor, when turning the floor, if not careful may lead to the edge of the floor veneer damaged.

Q:Do you have a grounding grid for your own anti-static floor?

The so-called anti-static floor is actually the conductive floor, people walking on the floor above, the friction generated electrons, the ground is conductive, the electrons through the floor into the bottom of the floor of the conductive glue and copper foil, copper into the underground conductor into the earth , So that the surface of the floor there is no charged electrons, there will be no adsorption of dust in the air. If not grounded, the electronic can not enter the earth, the floor will not play the role of conduction. Antistatic flooring, also known as a dissipated electrostatic floor, is a floor that, when grounded or connected to any lower potential, allows the charge to dissipate, with a resistance of 10 in the order of 10 to 10 Between the characteristics. "GB-2008 electronic information system room design specifications" provides: anti-static floor or floor surface resistance or volume resistance should be 2.5 × l04 ~ 1.0 × 109Ω.

Q:The room and shop the floor and the use of static wiring on the bridge wiring, scientific and reasonable?

Yes ah this is nothing is unreasonable is a practical request Many telecommunications room are used, Hengtong Xin Hong anti-static floor

Q:PVC pipe with anti-static performance?

Pvc tube is not anti-static but there is anti-static pvc tube

Q:Do the best anti-static flooring brand which?

The elephant floor of the brand should be the boss of the bar, sales have been very good, especially the old man prostitutes 薨 magic weapon for its quality, environmental protection is also good, as if the recent news that the elephant floor by the State Forestry Administration Awarded low-carbon competitiveness of the leading enterprises.

Q:Basketball floor floor how to deal with static electricity

You do not see someone at any time to wipe the floor, can not ask the point of nutrition

Q:All-steel ceramic anti-static floor. How can you open the hole? Used to take the line. What tools can I open the hole at once? Question added: .. both brick and brick but also ceramic tiles have not? To open the hole, what turned around? More

Although the tile is beautiful, but to punch on the tile is not an easy thing. Because the tile itself is easy to bad plus a hole is easier to break along the gap. Method / Step 1 ? The position to be punched is pre-calibrated to ensure the level. (Note that the corresponding location of the wall do not have water and electricity lines) 2, with a glass drill hole in the ceramic tile, the first tilt direction to play a pit; otherwise the tile is too smooth and bad positioning; or not all tiles, with nails directly A small pit to come; think about precision, you can also have a hole (size appropriate) plate with the best. 3, set out to play a small mark can remove the positioning of the orifice, and then. Prepare a bottle in advance, drill a hole in the bottle, the bottle filled with water. Then, when the hole to the water at the same time to the drill bit and tile contact parts; especially the whole tile, be sure to have water Oh. 4, there is no need to change the impact of the drill. Open the tile part, continue to play the screw depth. Attention to play a hole, remove the glass drill, the blocked part of the drill bit to clear the hollow. (All the tiles in particular to do this step).

Q:Anti-static PVC board where the use of, please give details of Thank you very much! The The Questions added: or what type of business with anti-static board, the best example Thank you ~ ~ more

Generally used for the production of anti-static floor, electronics and semiconductor industry used a lot, is the most cost-effective anti-static floor materials....

Q:Will static electricity cause a fire?

The electricity charged by static electricity is very small.

Q:Is it possible for ordinary household ceramics to be anti-static?

Ceramic can not be anti-static, but antistatic!