Automatic Chain Hanger Type Shot Blasting Machine for Large Casting Parts
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Q375 hook type shot blasting machine is suitable for bulk of large pieces of machinery and steel structure to make surface cleaning and blasting strengthen.to remove the welding slags and surface oxide;it aslo used for surface cleaning and strengthening for heat-treated pieces;and it’s used for fear,gear shaft,engine connecting rod,diaphragm spring,cannonball inner shell and other parts surface descaling after heat-treating to make the surface of workpieces to reach the color of silver-gray,and eliminate stress,improve surface adhesion of the coating;increase the surface stress ,improve fatigue strength to reach the aim of blasting stengthen.
This machine has the following features:
Shot blasting chamber body and blast wheel’s layout are determined by computer’s three-dimensional dynamic blasting simulation.
Adopts tbe world leading technology produced blast wheels, can improve enhanced efficiency greatly to get satisfaction strengthening effect,special sub-pill structure,so the utilization of abraisves can be increased by 15% than the old-style.
Separator :adopts the most advanced BE full shutter type & separator in the world,can increase separating effect greatly.
Adopts cartridge type dust collector,bigger filter area better filter effect.
Novel design ideas,easy maintenance.
This machine has automatic fault detection device.
You can decide the quantity of working blast wheel according to different workpieces size.
In shot blasting chamber adopts Mn13 shield,Increased the lifetime of shot blasting chamber
Mainly technical parameter:
size of cleaning pieces : 4000x2000x2000mm
workpieces conveying system(6 group in total,12sets)
cleaning speed 0.5-2m/min
conveying speed 0.5-4m/min(stepless speed regulation)
blast wheel : 12×11KW
bucket elevator : elevating capacity 140t/h
separator : separating capacity 140t/h
shot blasting chamber :
Shot blasting chamber is welded by steel plate and steel profile,its shape,size and layout of blast wheel adopts CAD optimal design,dynamic simulation, to ensure optimal throw angle and distance, the cleaning effect is best, and maximize the efficiency of equipment.
Each blast wheel will keep a certain angle with workpiece running direction at a certain angl, to ensure the cleaning workpiece be fully blasting cleaned (please see the blasting chart), and minimizing the empty throwing in the care of all the cleaning workpieces, thereby maximizing the utilization rate of abrasives, reduce the wear of shot blasting chamber.
Wear shield can protect the chamber body from wear, prolong the service life; the water toughening treatment of Mn13 rolling steel plate with high impact toughness, can make full use of kinetic energy projectile reflection, continue to effectively strike the work piece surface, is beneficial to improve the cleaning quality and enhance efficiency
- Q:I have to gain my wishes..People, somebody tell me. we were born, grew up, made choices (still making) and then society wants us to reproduce. Must everything be machinery?
- If you seek the reasons for being to start with, society today is just a bad play. Look toward more natural reasons for being, that is, think upon the meditative and forget the calculative that is our world. Just shut it out for a little while and get back to basics. Look for something beautiful in every day. If we could see the miracle of a single flower clearly, our whole life would change. --Buddha
- Q:Like Skynet from Terminator, there is a word they use besides quot;self aware.quot; A little help?
- Sentient?
- Q:Mechanical material forming cold forming and thermoforming What is the difference, the main processing of what materials
- Cold forming is not in the case of heating the material for punching, bending, stretching and other processing methods. Cold forming process cold forging, cold rolling, forging and so on. The main advantages of cold-formed steel structure: 1, compared with the thicker hot-rolled steel, cold-formed steel can be processed into smaller load and shorter span.
- Q:What is the processing of materials?
- The workability of the material means that the material exhibits excellent flow characteristics not only during injection molding but also excellent mechanical properties (strength, toughness and stiffness), short molding cycle (high productivity) and high temperature resistance (
- Q:Such as in terms of construction equipment like a crane, what is the maximum amount of weight that can be lifted by any existing machine?
- A crane's limitation is defined as metre-tonnes, because it is the moment that creates the limitation of the crane lift. A crane does the same amount of work to lift 50 tonnes at 10 metres as it does to lift 100 tonnes at 5 metres. That being said; I believe the largest single lift was perfromed by one of forty-two Lampson Tranis Lift IIs in Corpus Christi TX. The actual load was 1000 tonnes. And this just happens to be a MOBILE unit, on top of everything else!
- Q:I'm in 7th grade so please dont make this too difficult to understand.Thanks. :]
- try this site
- Q:why on ship machinery's are installed forward-aft & not port starboard?
- Depends on the designer... Machinery can be placed athwart-ship , fore and aft or a combination of the two if more than two pieces of the same type of equipment are installed. For athwart-ship placement at a given frame location, the numbering starts at the centerline and working outward even numbers go on the port and odd numbers on the starboard. For/Aft placement the numbering increases from bow to stern. Machinery is alway labeled starting at 1 even if it is located on the port side as would be the case of a single unit or the first forward most unit with additional units aft. Some factors that determine how and where machinery is placed include: size, weight, access for operation and repair, how critical the equipment is in relation to safe operation of the ship (number of backups or units to be run in parallel)
- Q:would these include non motorized equipment used for processing?
- Baler------ This is pulled by the tractor and used to make bales out of crops like hay. It makes a round bale that is 4'x4' tall. Each bale will feed about 25 cows a day. Combine------ This is used to harvest all kinds of crops. It does more than one thing--like pick and clean the crop. It has a sieve in it to get rid of the crop junk. They even have special ones if the farmer has lots of hills. Chisel Plow----- Plows dig up the soil to get it ready for planting. It will turn over the dirt as it digs. Cotton Picker----This machine picks cotton and puts it into the back. The cab has air conditioning and a cassette player/ radio/ and weather radio. It has a special seat for back support. Mower---- This is pulled by a tractor and mows down grass and low growing things. Row Planter---The containers at the top hold the seeds to be planted. This is pulled across the field that the farmer wants to plant. Row Planter---The containers at the top hold the seeds to be planted. This is pulled across the field that the farmer wants to plant. Seed Drill--- This is pulled by a tractor. It is used to plant grains and vegetable seeds. This can make different kinds of ditches that the seeds go in depending on what kind of soil there is. Sprayer--- This is used if the farmer needs to spray their crops for anything [like bugs]. It has a great cab, or place where the driver sits. The equipment company builds these to make farmers more comfortable while they work. Tractor--- This is one of the most important pieces of equipment that a farmer has. He uses it to pull equipment and crop wagons. The equipment company makes the cabs of these very comfortable, too. The farmer picks the tractor size based on what he wants to pull with it. ()
- Q:Where can I sell used printing machinery and equipment online?
- OKorder
- Q:it has for wheels and u can move around int it .... i can not think of its name!! PLEASE HELP =0
- Everybody is right; a gantry is called a cherry-picker sometimes. A scissor lift is another kind of mobile people-lifter. I saw a bulb changer driving down the hall changing lights on the high ceiling with a scissor lift. The guy changing street lamps was riding a cherry picker. Pick the one that fits the job.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
Automatic Chain Hanger Type Shot Blasting Machine for Large Casting Parts
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords
