Q:I'm trying to tighten the electrical wires on my car.Do I just use pliers and twist them tighter?Can I use my hands?-tightening the wires on my ignition switch and starterNeed to know asapNo B.S. just need to know how

Why you want to tighten the wires? If you meant position it, I would use zip ties, pull the electrical wire tight is not a good idea.

Q:The output part of wire plastic and part of wire broken, and the connection lost sometimes, some taps used to wrap up but the connection is still not good.How to fix it permanently?

Only try to fix it if it is on the lptop side, DON't play with A/C power unless you're qualified. If it is on the safe voltage side you could cut the wire, strip back the wires about 1cm, and twist them together, then solder the wires. Before you join them slide a small piece of heatshrink over one side of it, then after joining and soldering the wires wrap a small amount of electrical tape around the bare wires then slide the heatshrink over it all and heat it up to enclose it all, Fixed ! If you need help with it let me know. Cheers,

Q:Is it better to have a wireless internet connection or a wired connection for my ps3 online games?

Wired always provides more consistent performance, regardless if you're playing on the PSN or surfing the web.

Q:I bought these speakers and I was wondering what kind of wiring do I need to get to wire them to the amp?

Wire okorder /Product/Product.as...

Q:I bought a bathroom vent fan today, the one that was in there hasnt worked since we bought the house. Anyways, i have a black wire, and a white wire coming from the light switch on the wall ran up to the ceiling where the fan is, and a black, white, and GREEN comin off the new fan i bought. Do i need to get in the attic and run a ground wire from outlet to fan? Or are the black and white good enough? The old fan didnt have a ground wire, just the other 2. Any info is greatly appreciated. Thanks

Green wire should be screwed into the inside of the receptacle box or pigtailed to the bare copper wire in the back of the box. If neither a bare wire or a green screw is present, call an electrician to run proper wiring to the box

Q:TRUCK WIRES, quot;orange,yellow,,red,,black,,white,,brownSTEREO wires ,,Yellow,red,black how do i hook this up right ? HELP !!

This one is the best wire. Pyramid RPB10100 10 Gauge Black Ground Wire 100 Feet OFC Technical Details * 10 Gauge Black Ground Wire 100 ft. OFC * 15/0.25 x 7C,D. 5.0mm

Q:In the ceiling is one black, one white and a ground. How do I connect a new ceiling fan to these two wires? The ceiling fan has black wire, white wire, a blue wire and a green wire. We don't have green in the ceiling nor do we have a ground...knob and tube perhaps? So, can we connect this fan or not?Thanks!

Personally, I would not connect anything to old knob-n-tube wiring. I would replace all of it with modern wiring. And as for a ceiling fan, not only does it require a box designed for ceiling fan support (which I doubt you have right now), it also requires 3 wires, served by a 14/3 Romex with ground. It will have a black, white, red, and bare ground. The red wire is for the light, black for the fan, white neutral, and bare copper to green ground. On the wall, you will need a double-gang box containing 2 devices. One is a standard light switch controlling the light. The other is a fan controller unit ($12.49 at Home Depot) for the fan speed. It has 4 click-stops, High, Medium, Low, and Off. It uses a standard double-switch wallplate. On the fan itself, cut the chains off. Be sure the fan is set to HIGH, and the light ON when you cut them.

Q:Im wiring my pioneer deh x3600ui to my pontiac grand am gt 2002 directly without a factory harness. Any diagrams out there i can use? The red wire on my pioneer is for the ignition but i cant find that wire on the pontiac.

if u cant find a diagram u can always check the speakers for the colors of the wires and then just try to get a hold a cheap little voltage meter like the one below just to find ur ground, remote, and battery wire.

Q:whats a good brand for 0 gauge wire to get? im looking for a good brand that has 100% OFC wire, i would get knukonceptz, but their wires are copper coated aluminum which isnt as good.

www.okorder

Q:I'm just wondering would i be able to connect a split 8 gauge wire with wire nuts like i'll explain:Use two wire nuts instead of one and divide the copper wire on both ends and wire nut both sides together with 2 nuts. The whole apparatus would look kinda like this:----lt;gt;---- with the wire nuts connecting the two arrow thingsThanks anyone

Even though you had been wise to make use of the noalox, or antioxidant, i might ratehr endorse that you get the suitable gauge of wire in copper and rewire the entire circuit. The intent that I say that's that your oven is a excessive resistance circuit and aluminum does no longer like high resistance. With excessive resistance on aluminum, the aluminum wire will start running or moving under the strain and can eventually burn out the connection. In the event you have got to leave it aluminum, don't use a wire nut, but get a split nut from an electrical provide, use teh same goop on it, then get two wrenches for the best way that you just ought to screw the break up bolt to the nut, tighten the item down as tight as humanly viable, the wrap it with a specified tape that the electrical give may also have. It's not the commonplace electrical tape, but a stretchable tape and also you wrap it tight at the least 3 or a bit of extra inches on all sides of the nut. This may insulate the connection in order that it are not able to be shorted out in any respect. Mine had the same aluminum connection and when I changed the stove, which was difficult wired to the stove, I simply replaced the entire wire. Mainly the field is just not too some distance away fromthe stove due to the fact it wants to be as just about it to decrease resistance. To scan what you have got performed, that you would be able to take a low-cost volt meter from Radio shack, set it on the correct settings for measuring voltage on 220, and if the needle goes to 220 + or - a bit, you're nice in the meanwhile.