Q:Has anyone tried to use or experiment to use CAT5E wire on a speaker going to Home theater receiver? If none, can you suggest a good speaker wire to use on a speaker.Paradigm Monitor Series and Onkyo TX-SR606 (Speaker and Receiver)

In my opinion, stranded individual wires degrade the sound, while thin flat copper foil gives the best sonic result. The difference is truly amazing.

Q:I want to make wire art but I'm not sure what type of wire to use

They also sell rolls of other wire, click on metals in the top sequence, choose one then choose wire.

Q:one single coil pickup (white wire and bare wire)and one volume pickupidk how to do it thought it would be simple but obviously notdiagrams would be awesome

Are you experienced in this sorta section? i could easily propose that in case you recognize somebody who can try this sorta stuff no difficulty, ask them to take you thru it step via step.. besides the undeniable fact that the mixture sounds good besides the undeniable fact that, I fairly like the sound of that..good success and satisfied enjoying :)

Q:where can i buy these type of wires (copper insulated wires)??

You can buy it at the suggested locations. Insulated wires come in many types for various uses. Be sure the person you buy it from knows the use for which you are buying it. For instance, wire or cable for underground use is far different from house wiring.

Q:So ground wire, start anywhere i suppose?Where does ground wire hook up too?why you need to ground out your system?Only need 1 ground wire?

yes only one from the amp to the battery with an inline fuse

Q:I know I am suppose to run the RCA cables and power cables on opposite sides of the car, but which side do I put the speaker wires on, ps I have an amp so I'll be running the wires from my trunk

in my car i ran the speaker wires on the same side as the RCA's

Q:me and my friend were doing a circuit challenge and we did the same circuit but she used thicker wires. does it make a difference?

Well that depends upon your friends circuit. But, I can only add to what has already been said by saying this: - Using thick wires is traditionally associated with passing large currents in a circuit. However, if you use low voltages with thin pieces of wire (especially if it's long piece) then that can have a significant effect upon the circuit you are trying to supply. This is because the wire has resistance of its own that may well me nearly the same as that of the circuit you are trying to supply. All of which means that there may be a considerable voltage drop across the wire and less for the circuit you are trying to 'feed'. So, ironically, although thick wires are traditionally used for high current circuits they may also be found to in low voltage circuit passing very little current; the point being that we want a small a voltage drop as possible to appear across the wire. To illustate using a example, suppose that you are having a garden party or BBQ and decide to have some disco music outside. You set up the speakers outside while keeping the stereo in the house. You know that the voltages and currents are quite low so you think that more of the same cable that is already connected to the speakers would be fine. You run out the lengths to the speakers and switch on only to find that the volume is way too low even with the volume knob wound right up! What has happened? The resistance of the cable with the lengths that you are using is now comparable to the speaker impedance and this means that there is a voltage drop between the ends of the cable meaning less for your speakers. The solution is to use really thick cable, like mains cable capable of taking 10's of amps; it's not the current rating of the cable that you require but its low resistance.

Q:I need to get to the audio wiring

you cannot simply go with matching the colors factory radios have extra wires that are not needed with an aftermarket install most of the time (wires that control the dimmer on the radio, speed sensitive volume) you will need three power wires (constant, ignition, and ground), plus your speaker wires use a test light to test your wires, usually at the radio the yellow wire is your constant, the red is your ignition, and black is always ground to find your constant use the test light, it will be hot at all times so that your radio can remember the time, and your settings- next you need your ignition, it is only hot when the key is on or in the accessory position, to tell the radio when to come on- the ground is self explanatory to find which wires go to what speakers all you need is a 9v battery, put the positive end to a wire and test all of the other wires to the negative side and you will hear a crackling noise from a speaker when you have the right combination

Q:which color is the positive and negative wires on the speakers of a 1993 F-150 one is red and one is black..

door speaker wires 150

Q:I Have a 02 Dodge ram with the 5.9L engine and i purchased a O2 simulator because i wanted to remove the cats. what i need to know is which wire is the Signal, 12 volt, and the ground wire on the oxygen sensor. If anyone has any idea please share some info.

The wires should be color coated. Usually if it is a 4 wire o2 there are two white wires and two black wires and the blacks are both grounds. Same should go with the 2 wire o2 the black is usually the ground and the wite is the 12v wire.