Q:Which of the following wires would tend to have the least amount of electrical resistance? a) long b) fiberglass c) hot d) thick

thick wires have less resistance

Q:How can I stop my cat from chewing wires? He does it all the time, and the wire he ends up being important.

Get yourself a little spray bottle/squirt gun and spray him when he bites on the wires. hopefully that will condition him not to do that....I have 2 cats that both chew on wires and that worked on the first one, but not so much the 2nd yet.

Q:I have a audiofonics adf-240 and I want to wire it to 1 ohm

you do no longer cord the amp you cord the subs. seem up the wiring optons on your subs and notice the thank you to drop the ohms. remember you will make greater potential yet your amp will run warmer and wont final as long except carried out properly.

Q:wire diagram and manual

From Rinker. Or from Nautic Global Group as they now own Rinker since their merger with Godfrey Marine.

Q:i want electrical symbol used in house wiring

The electrical symbol for what? Different devices and types of devices have different symbols. Also, each architectural firm uses a slightly different set of symbols so that a particular symbol on one set of plans will mean one thing, but mean something else on a different set of plans by a different firm. An UGLY's Book will give you some of the more common electrical symbols.

Q:i need an egr wiring Diagram for a 2000 Chevy Malibu. the wires got pulled out of the weather tight connector. if anyone can help i'd appreciate

Connector view for the GM linear EGR valve are as follows: Pin# A=gray/w black wire,Pin# B=solid black wire,Pin# C=brown/w white wire,Pin# D=brown/w white wire(see note) and Pin# E=solid red wire! NOTE since pin C+D have the same color wire the correct wire must be identified by checking the voltage with the KOEO (key on engine off) the right brown/w white wire should have a 5volt reference voltage with the key on engine off! Hope this helps.

Q:Can I use 12-2 gauge wire on a 10 amp breaker to wire my light switches,and can I use 10 gauge wire on a 10 amp breaker? For a light fixture

Normally lighting circuits have a 15 amp breaker for protection and wired with 14 gauge wire. 14 gauge wire is good for 15 amps. 12 gauge wire is good for 20 amps. 10 gauge wire is good for 30 amps. So you can use 12 gauge wire, if you alrady have it available, but if you are going to go out and buy it, you can save some money by buing #14 wire. You can always go oversize with the WIRE just never undersized with the wire. Circuit breakerprotection is prescribed by the NEC. 15 amps for lighting and 20 amps for wall outlet power. I don't know where you even found a 10 amp breaker. ---------------------------------------... WOW! XTX has no clue what the National Electrical Code even says about this! Disregard his answer! It will get you into trouble!

Q:I have a Escort 8500 x50 that I want to use in my 04' Chevy Trailblazer, I bought the hard wire kit, but which is the quot;positive ignition wire?It already includes the T-Tap I just don't know which wire to tap into! Any Help would be great!

The positive wire should be red and the ground black. You should tap into a wire that is ignition hot. Meaning it only has power when the ignition is on so it won't run down the battery. The easiest one to use would be the accessory port on the fuse panel. The ground needs to go to any good metal part. Find a screw that is in a large metal part, like the dash support, and wire it under the screw.

Q:What's the best kind of wire to use that can stand being kilned?

that really depends what you want to do and how high you are going to fire. Generally nichrome 80/20 wire should be OK until cone 9. Then there is Kanthal which will withstand even higher temperatures but is more expensive than nichrome. You could get either probably in electronics supply houses. If you do lowfire, maybe up to cone 06 or lower steel will probably be OK. The surface of the steel will oxidise and so get clearly thinner, keep that in mind. Generally your wire and the clay should not be in direct contact because they have different thermal expansion coefficients. Depends how rigid your wire is if it will lead to major damage to your piece. But if you wrap your wire with paper before you put clay around it it is probably OK as long as you don't enclose the entire thing with clay into a hollow space. But it also depends on what exactly you are trying to do, e.g. what kind of clay you are using. Mostly people use wire with clay for making beads. If that's what you are doing you can also look up bead making techniques.

Q:What are the range specs when testing resistance on your spark plug wires ?

RE: What range in ohms are spark plug wires normal? What are the range specs when testing resistance on your spark plug wires ?