Q:So I have a ordinary pc with a 500gb seagate hardrive in...and I have another seagate hardrive I want to put in (also 500gb) but do I need the sata power cable since it is not the main hardrive or can I only insert the Data cable for the harddrive since I didn't get any cables with my hardrive do I need need both cables, the Data and power cables or can only use the data cable ?

yea you need both, the data and the power cable. Power need to go to the hard drive via the power cable and the hard drive need to communicate with the motherboard via the data cable.

Q:i am going to establish a new power cable manufacturing business. i want to ask you what should i name to my business or what brand name should i adopt that is appopriate.

follow the suggestions. Good Luck

Q:So, yesterday I went to a bargain store and I found a Memorex MiniMove Boombox for iPod for 15$ because it didn't come with a DC cable. It has a battery function but it will only charge my iPod if its plugged in. I've been browsing OKorder for a DC IN 6v power cord like it calls for, but I was just wondering if there's anything else I need to be aware of before I consider buying one. Everything else works great, but I really need a charger as well as the stereo because my mom broke my last one and now it work play anything relating to my iPod when its plugged in but that was the only alarm clock I had. Thanks!

Hard to say for sure. Your best bet is to go to the Memorex site and see if you can download the user manual that will have the full specs for the power cord. Then you can match everything.

Q:Cable YJV-1KV-5 * 10 pipe laying, including cable head system with what fixed amount?

KVV is the control cable, generally do industrial control; and RVS is twisted pair, generally used for weak system, to eliminate the interference requirements of the occasion, such as two-wire bus system, specifically, the electrical fire bus more Such as RS485 bus and so on.

Q:I'm extending one of my PSU power cables because is to short. the line got 2 black/1 yellow and 1 red (molex) I know the colors have to be matched but if at the other end I end up mixing the 2 black lines, will there be a problem?ps: I already sleeved the cable for that matter I can't see the 2 black cables inside and i forgot to mark them. :)

swapping the black wires will not cause any problems.

Q:Does the nvidia GT 520 require any power supply cables to be attached to it or do only the mid/higher end cards like HD 6870 require psu cables to be attached?Thanks

for low end cards, you dont need an additional 6 pin or 8 pin power cable for it. It is only for mid range and high range cards that need additional cable for it. For GT 520, you don't need it.

Q:What kind of cable does the power cable 3 (1 * 240) +2 (1 * 120) Is it a separate cable?

Although there is a relatively thick cable inside the cable to prevent a very thin cable was broken, but the insulation is not iron, after all, is generally a VB tube is also a corrugated pipe PVC pipe is also too iron

Q:is it possible to split the live wire feeding my car stereo into 3 feeds so one is my stereo , two is my satnav power cable and the 3rd is my reversing sensor display. will this overload the wires? any advice how i can do this would be most helpful. thanks

I'm assuming you mean the wire providing the 12-volt power to your radio? And you want to connect other unit's it? It all depends on how much current is drawn by the additional units. Do they have fuses? What sizes are they? Backup cameras usually draw very little current and have really thin wires. Shouldn't be a problem. What type of navigation device? Does it use a DVD-ROM or is it just on a chip, like a portable Tom Tom, Garvin, etc.? If neither of the units' fuses exceed 5 amps, I'd say you're safe (in most cars) running it from the radio's power wire. However, you didn't state the type of car. Late-model GM cars or Audi/Volkswagen have low-current radio wires that use computers. They are known as data bus or can bus systems. I'd avoid connecting to these.

Q:98 dodge intrepid, wanna run power cable through the firewall without drilling a hole.

actually i could Run The twine interior the Truck Why? with the aid of fact the insulation Of The twine Is Gonna placed on Out., and you on no account understand a pointy merchandise would shrink Your twine And reason a short or possibly a fireplace... i could Run It actual next To The Seats decrease than Neath The Carpet..

Q:How would I go about stripping 4 gauge power battery cable for my amp? oh and how would i screw the fuse holder down? with what kind of screws? thank you!

I use a knife to strip that wire, just be careful not to nick the wire. Drill a hole and use sheet metal screws to screw the fuse holder down.