Q:ill exlplain more the battery is connected to one end of the fuse then i want to run 2 power cables out of the other end to both of the amps will tis work or will i just loose power the fuse is 60A if that helps. 60A is massive why a fuse that big is needed i dont no

You will need to run a wire to each amp using a fused distrobution block as mentioned. A 60 amp fuse isn't really that big for car audio. Some amps can pull 80 amperes. This fuse is really only there to protect the power wire from being shorted.

Q:My power supply cable to the motherboard is only 20 pin and the motherboard has a slot to take a 24 pin power cord. The 20 pin will fit but 4 slots are just left empty. The motherboard LED light comes on showing it has power. When I try to boot up the motherboard runs but the hard drive doesn't boot or the screen isn't working. Could this be b/c of not having a 24 pin power cable?I know the video card and HD work b/c I just transfered them from another motherboard that was a 20 pin. Any ideas?

yes it will... most of the power cords are 20pins now... the mobos are built for 24 just for compatibility with some rare power supplies... just stick it in all the way to the left and leave the right 4 pins empty... about the boot problems check your RAM speed... more than likely you have old RAM sticks that cannot run on your new mobo (by the looks of it it seems like you just purchased a new one)... most new motherboard will not take anything less than 400MHz... I think you will have to purchase new RAM too... that is usually the case...

Q:I have a Karcher power washer which was left outside over night. An animal chewed threw the power cable and so is unusable. I was wondering how to re-connect the power cord together, safely. I do not want to cross wires and use electrical tape. I was thinking of using a connector, but unsure of whether to use a two pinned or three pinned connector.

You can install a plug on the cord to replace the one that was chewed off. Choose one with the same number of prongs as the cord has wires (2 or 3). Be sure to attach each wire to the correct terminal! Splicing the cord is also OK, and tape would not be a problem if applied properly, but I prefer to use heat-shrink tubing. When I do a top-grade splice, I first twist the wires tightly together without making a tail, then I solder them.

Q:I currently have a 250 watt 2 channel power cord and a 500 watt alpine amp with 2 12 inch mtx terminator subs.i am continuously blowing blade fuses and i ended up buying a 680 watt power cable. Will this blow out my amp or do any damage or will it be all good and give the maximum power my amp can supply? (Without exploding) just wondering thanks!

250 watt power cord? Where are the fuses which are being blown? Maybe you put in the wrong fuses or the wrong amperage fuse.

Q:I looked on 3 of my friends plus mine and looked at the cord that comes from the big block power supply thing for the xbox 360 and every one of them looked differant. Why is that?

cause they felt like makeing them different

Q:Excuse me, what is the difference between submarine power cables and general buried power cables? What is the difference between the calculated current carrying capacity of the submarine power cable and the general calculation of the current carrying capacity of the cable? More

It is the audio cable connection is not good, you check the line and the machine at both ends of the socket is rusty, for the new line can be. In addition, the TV volume will be reduced, the set-top box volume can be filled!

Q:holes to route the cable through anyone have pics or a website so i can figure it out

steering rod boot or drill a hole

Q:If you have an electrical device (e.g. a laptop), you'll sometimes notice that near the place where you plug the power adapter into it, there's a sign. It's composed of 3 circles, minus on the left, O inside a C in the middle, and plus on the right.What is this? And if I want to read/learn more about it where should I go?

If you look at the jack that go inside the power input you will see that it is an outside connect and an inside one.The O is the inside connect and the C is the outside one.Because it is a DC power adapter it has a + and - polarity .O,the inside ,is the plus and C,the outside,is the minus. Also on the adapter you can see the same thing! This is because some brands use the outside connect as + and you can burn your device if you use it!!!!

Q:I need a 3.5mm 5V DC power cable with a USB input. I do not want to order one online. What store would sell this? I already went to Best Buy and Radioshack.

Sorry okorder / You will be fine and wont be scammed. OKorder is a possibility but its a tad sketchy but its easy to use and not get again scammed but its your choice ofc i don't know the situation your in. im just guessing your worried about ordering online due to scamm websites, it could be that you simply don't have a card that can shop online (or even a card). Also delivery should be fairly quick (most being a week) so you won't be waiting too long either way. Turtle beach is based online, and distribute mainly from their website,(such is most designer accessories) the only reason they have their products in stores are because of their success online, and were able to expand but even then they only ever sell a few of their headsets in stores never their full range, then expecting parts is very rare. p.s i realise its a generic piece of equipment but its quite specific and there are very few things that use somthing that you've specified (not the sized and volt just a DC power cable that has a USB input) , that includes headsets, seriously most headsets don't require a power cable (and it having a power cable doesn't make it good) Hope this helps :S

Q:Every time i unplug the power cable from my laptop the wireless connection stops working and i can't seem to fix it by changing the wireless power options any ideas?

I am assuming that you are using windows, If you haven't done so already, right click on the battery on the right hand of your task bar and click on the power options. now, click on CHANGE PLAN SETTINGS Then click on CHANGE ADVANCED POWER SETTINGS a new window should pop up, look for wireless adaptor settings and select maximum performance, This could be your answer but then again I'm not sure what you have already attempted.