Q:How do you increase your product? How do you assign multiple segments? Speed? How to determine the holding position? Big, good or small? All help answer! Be deeply grateful！

The distribution of each position and velocity, if familiar with the products of the case, according to the previously adjusted product size, short range, reducing the pressure and speed, the adjusted number of a few know it, and then slowly add pressure and velocity, and material. Process debugging did not say big products, good tune or small products good tune, this with your craft level, material, mold, equipment and so on have the factor.

Q:What kind of after-sales service, which friends know to introduce?

The best thing is the company's low pressure injection molding machine, and many famous brands are looking for them to process low voltage injection molding machines, such as apple, Microsoft, and the United states.

Q:Not computer, there is a proportional current. The whole machine has no hydraulic operation and the pressure gauge is zero.

2 、 injection molding machine, also known as injection molding machine or injection machine. It is a thermoplastic or thermosetting plastic plastic molding mold made of plastic products of all shapes of the main molding equipment. It is divided into vertical, horizontal and all electric type. The injection molding machine heats the plastic, applying high pressure to the molten plastic to make it crack and fill the mold cavity.

Q:How to debug the injection molding machine? solve

You ask too many questions, and debugging involves so many things. If you mean that a process problem is not clear, or you can do other debugging on the injection machine, you can write it out. Plastic injection is not difficult. As long as you are willing to learn, you will not succeed if you depend on it

Q:The higher the screw speed of the injection molding machine, the higher the oil temperature

The higher the screw speed of the injection machine, the higher the oil temperature, which is normal, because the screw will rotate continuously and friction of the material, friction will produce heat. We generally cold water machine injection molding machine can be equipped with a mechanical product in Europe, so can increase oil temperature control.

Q:Seek advice! Is there a better low-pressure injection molding machine? After the sale well, which friends can introduce, thank you!

As far as I know, the low pressure injection molding machine produced by Connie Technology Co., Ltd. is especially good and provides full range of technical support, which is rich in New Technology

Q:What is the gear adjustment and chain adjustment of the injection molding machine?

It is the die adjusting mechanism on the tail plate of the injection molding machine. The gear adjusting die is to drive a big gear with a regulating motor, and then the big gear drives the four small gears on the forest column to realize the adjustment and advance of the die.

Q:Vertical injection molding machine in the semi-automatic state, not sol, and sometimes sol is very slow, seems to be very difficult, and sometimes simply do not turn. The problem is that it occurs during normal use, so the temperature should be fine. The parameter should be OK, too. I removed the screw and cleaned it. There was no foreign object. Under manual operation, the sol is very smooth. Consult an expert.

Mainly back pressure problems, a lot of injection molding machine, manual adhesive and automatic adhesive in the back pressure is not the same

Q:Process knowledge of plastic injection machine head

The utility model has the advantages of: two face wear less, good plasticization. Disadvantages: outer wear quickly, and the barrel bore tolerances or when the debris falling into the barrel in the easy to cause the whole screw does not turn over the other is like. The apron will accelerate the cylinder bore wear. A rubber ring outer wear slower without fork and because it is not how to rotate in the pre plastic, but both ends of the surface wear, if you want to do PVC or PC and other plastic material, with the rubber ring is better, because it can avoid the dead corner so as to avoid the buildup the dark spots. Transparent injection molding products of plastic head ring: three meson screw head small overall smooth surface, in addition to the assembly part outside any one can see the front of the place can not have right angle corner, all parts should be based on the angle of smooth transition. Because the right angle corner, easy crack is not that also easy to make accumulation of materials. The material flow is not clear. For a long time to have three small yellow spots, usually is the most prone to yellowing of the site, do a lot of transparent PC.PMMA products are for three sets of design is not good, resulting in yellow.