Packaging & Delivery of 0.9mm Steel Tape For Armouring Cable
Packaging Detail : In standard Packing
Delivery Detail : 25-30days
Specifications of 0.9mm Steel Tape For Armouring Cable
cable tie mount
Material of 0.9mm Steel Tape For Armouring Cable
Nylon 66,94v-2,certificated by UL.Acid and corrode resisting,insulate,not to age,with imported double sided tape on the back.
how to use:
remove the cover of the adhensive and stick the piece properly,then put in cable tie for using.
- Q:Wire printed on the word what way to erase
- If you need an unqualified wire, you can contact this part
- Q:Ipad charging display does not support this accessory
- Ipad charge display does not support the general reasons for this and processing methods: . for non-original charger, it will often appear this situation, which is due to the charger does not meet the specifications caused by the replacement of a qualified charger can be. . if the original charger appears the above failure, please continue to look down. . please check whether the data line is normal. The appearance of the data lines seem normal, which may have been broken. Check the method is to borrow someone else's data line to see if it can charge. . shows the plug symbol is normal is full of display. If full or show the lack of electricity, indicating that the phone tail no problem. . again, check whether the original charger can work properly. You can connect the charger to other USB port to see if the phone is working properly. . if the above two check still can not charge, please try to insert the computer's USB port to see if the computer can identify the phone, to identify if it is to see if the charge, if not identified but not charged, it is estimated that the need for maintenance. If you can not identify can not charge, it is necessary to repair. If you can recognize and charge, replace the data cable and the charger (the original estimate is also damaged). . and then look at the voltage is not too low, not only to the maintenance station to repair, and pay attention to the iPad and iPhone do not mix the power adapter, the voltage is different.
- Q:Is the toilet wire walk on the ground? Are there any hidden dangers?
- The proportion of the cross-sectional area of the cable through the embedded pipe is 20%
- Q:The computer can not open the machine display frequency beyond the scope of the mouse and keyboard do not start can not press F8 how to do
- Several sets of cables in the same height of the laying, the adjacent cable between the bridge should be considered maintenance, maintenance needs, generally not less than 0.6m. This is just a matter of theory, it does not matter. Anyway, the actual construction is to do so,
- Q:2.5 square copper (green, with the threading tube) can withstand the highest power of several kilowatts,
- Should be the line group: lighting a group of 2.5 square millimeters, an ordinary socket a group of 4 square millimeters, air conditioning a group of 6 square millimeters, kitchen and bathroom appliances a group of 4 square millimeters, so that after the down is not enough to put a separate group You say the high-power electrical outlet, the line to the square of the square mm to see your home how high-power electrical appliances, but advise you to use these high-power electrical appliances before the first to determine its current good, More than your home appliance load!
- Q:Seeking the basement of the outer wall piercing the cable after the casing, how to solve the water (200 points online)
- Line width, and can not pass the gap between the chip pins, even after, but also because the distance between the wire and the lead is less than the electrical rules specified in the safe distance. In general, the ground can not pass through the gap between the chip pins, go outside or take the gap between the two columns through the gap. The width of the ground wire can also be set appropriately, and the wire is widened by adding a polygon brass cut. The safety distance in the electrical rules defaults to 10 mils, which is relatively small, and the safety distance of the different networks should be set separately as needed.
- Q:What is the cable for rvv? Is it a power cable or a control cable? What is the cable?
- The installation process is a certain requirement, high and low voltage cable bridge should be installed separately as usual, a wall laying vertical pipeline (slot) or installation equipment, the power distribution between the depth of D1 = 1200 ~ 1500mm; weak Between the deep distance from the D2 = 1100 ~ 1400mm more reasonable. The length L1 and L2 between the power distribution and the weak can be determined according to how much electrical equipment and pipelines (slots) are installed in the room. "Civil building electrical design specifications" proposed "shaft size in addition to meet the wiring spacing and terminal box, distribution box layout must be the size, but also in the box before the left not less than 0.8m operation, maintenance distance" requirements. In the weak equipment, the operation and maintenance distance is not specified in the provisions of the Code for Electrical Design of Civil Buildings, but it should not be less than 0.8m. Cable to wear steel pipe wiring, should be reserved in the floor steel pipe, wiring should be completed after the plug fire fire blocking material. Cable bridge installation should be horizontal, the maximum sag should not be greater than 10 mm; proposed separate installation
- Q:What is the difference between "wire" and "cable"?
- Inkjet printer is not printed, pictorial machine high definition, generally used in the advertising industry, for large outdoor advertising, the nozzle can choose not necessarily the number of installed, the more spray, spray the faster, a nozzle of the general life 1 year.
- Q:What does the letter of the computer cable model mean?
- The meaning of the letter: W refers to the halogen-free, D refers to the low smoke, Z refers to the flame retardant WDZ is halogen-free low smoke flame retardant jacket power cable. WDZC refers to halogen-free low smoke C-class flame retardant
- Q:Home wiring is a good line or a good line? Talk about the difference
- LCD TV can not be connected to the top of the box and DVD reasons: the connection line is wrong, you need to re-connect the video cable or high-definition multimedia interface line, component color line. . the first audio and video cable to DVD and LCD TV ("video 1" or "DVD" signal source); . Moreover, the set-top box and LCD TV (HDMI1 . the LCD TV, DVD and set-top box power are open; . according to the source selection, if you want to watch the DVD program, put the signal source to switch to the "high-definition multimedia interface cable (HDMI cable) Video 1 ", if it is to see the set-top box program, put the signal source to switch to" HDMI1 ". . so that put DVD and set-top boxes are also connected to the TV.
We mainly produce conductive master batch for ABS, PP, PE, PS ,PA, POM and PC. We also produce anti-static master batch, UV master batch, strengthening master batch,, whitening master batch, toughening master batch, PP flowing master batch, PP environment proof flame-retartant master batch, lubricant master batch etc. Different kinds of colors are available, such as golden color batch, silvery color, pearlescent color, fluorescent color, blue, yellow, orange, black
1. Manufacturer Overview
|Annual Output Value
||Southeast Asia;Mid East;Domestic Market
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||70% - 80%
|No.of Employees in Trade Department
||Above 8,000 square meters
|No. of Production Lines
||OEM Service Offered; Design Service Offered
|Product Price Range