Waterproofing Concrete Floors

Hot Products

F-type (water only) New Building Materials

Short fiber Needle Punched Non woven Geotextile

Interface agent New Building Materials

Galvanized Gabions net PVC Coated Gabions net for River Bank Bridge

LLDPE Geomembrane for Environmental Projects Water Conservancy Projects Landfill Mining Canal

Aquaflex KS-988A JS High Polymer Modified Cement Elastic Waterproof Coating

High Elastic And Thick Acrylic Waterproof Coating

dry powder JS waterproof material New Building Materials

Polymer-modified cement compounds for waterproofing membrane

Steel-plastic Geogrid with Convex node for mine

FAQ

How do you make waterproofing in the kitchen and bathroom?

Fatty acid cement mortar waterproofing agent; integrated current domestic and foreign new waterproof material of the latest technology, in the original polymer cement mortar waterproofing agent developed on the basis of raw materials imported from Germany, the higher fatty acid materials, by more than 20 kinds of raw materials by the special complex Chemical reaction of water-based emulsion, a new type of fatty acid cement mortar waterproofing agent.

How does the finished ventilator manufacturer waterproof?

do not play any silicone and tape, to avoid the silicone tape aging caused by leakage hazards. Can be done once and for all.

Why should the use of high pressure perfusion waterproof plugging method

High pressure grouting construction principle: is a special high-pressure grouting waterproof material through the high-pressure infusion equipment into the concrete crack structure extended until all the cracks (including the naked eye is difficult to meet) filled with water (water) with the cross-linking reaction, Release a large number of carbon dioxide gas, resulting in secondary pressure, high pressure and secondary pressure will be pressed into the elastomer and filled with all the gaps, to stop the purpose of leakage, it can be said that the best performance of plugging material,

Find the construction steps for waterproof coatings

2, waterproof layer construction sequence and methods (1) base surface treatment and acceptance of qualified, and now Yin, Yang angle and construction joints and other special parts brushing waterproof coating layer, strengthen the layer 1 mm, strengthen the layer after brushing, immediately paste fiberglass cloth or 30 ~ 40g / ㎡ polyester cloth reinforcement layer, is strictly prohibited to strengthen the surface layer and then paste the reinforcement layer material. (2) to strengthen the layer of hard work, began to brush a large waterproof layer, waterproof layer using multi-channel (3 to 5) brushing, brushing the upper and lower coating should be perpendicular to each other. When the surface of the coating is completely cured (not sticky hands) before the next curtain coating construction. (3) polyurethane coating waterproofing layer after the completion of the experience of acceptance, the timely application of the waterproof layer of the protective layer, the plane protective layer with 7 cm thick fine stone ㎝, in the pouring of fine stone before the need to cover the waterproof layer A layer of 350 # paper tire linoleum insulation layer. Facade waterproof layer (such as anti-beam facade) with a thick 6 mm polyethylene foam protection (expansion ratio of not more than 25 times).

Nanning building waterproof material market where

to buy what materials are going to go to some factories, such as paper, printing materials and other manufacturers in the Nanning High-tech Zone or Nanning Economic Development Zone may be more

How does the waterproofing membrane work?

2, in accordance with the roof slope in the direction of the parallel roof will be placed in the waterproof membrane, and unwound;

Finished house bathroom waterproof household acceptance should be how to accept?

3: waterproof cement mortar leveling layer and foundation with dense, no hollowing, smooth surface, no cracks, from the sand, yin and yang angle made of circular arc.

How to do waterproof bathroom, construction process is what

Second, the construction process: 1, grass-roots treatment: grass-roots surface must be smooth and smooth, there must be no pit phenomenon may not loose, trachoma or hole exists. If the above phenomenon should be smooth and smooth after the construction, the surface must be dry, there must be a pipe at the root of the head must be wiped into a circular arc, the pipe must be strong. 2, brushing the primary treatment agent, the "Liang wall" waterproof primer at the end of uniform mixing, and then use a long brush or rubber brush scraper, scratching the waterproof material, even brush to the grass-roots level, brushing Can not be stacked and exposed white bottom, brushing the amount of each time to 0.4kg / square meters is appropriate, the first time after the full dry before brushing the second time. 点击图标下载 App