G3000 Cast Iron
G3000 Cast Iron Related Searches
Wrought Iron Mesh Sheet Large Rolls Of Plastic Sheeting Pipe Scaffolding Iron Outdoor Bench Upvc Pipe Properties Pipe Gre Rfp Pipe Dicl Pipe G3500 Grade Iron Castings Characteristics Of Hydrochloric AcidHot Searches
Buy Alabaster For Carving Alcoa Aluminum Stock Price Today 1 4 Aluminum Plate Home Depot 1/4 Aluminum Plate Home Depot 1 8 Aluminum Plate Home Depot 1/2 Inch Aluminum Plate Near Me 1/4 Inch Aluminum Plate Near Me 1 4 Inch Aluminum Plate Near Me Aluminum Tread Plate Home Depot Aluminum Trim Coil Near Me 1/2 Aluminum Plate Near Me 1 4 Aluminum Plate Near Me 1/4 Aluminum Plate Near Me 3/8 Aluminum Plate Near Me 1/8 Aluminum Plate Near Me 3/16 Aluminum Plate Near Me Aluminum Bar Stock Near Me Mic 6 Aluminum Plate Suppliers Aluminum Round Stock Near Me Wholesale Drill Bit Price PhilippinesG3000 Cast Iron Supplier & Manufacturer from China
Okorder.com is a professional G3000 Cast Iron supplier & manufacturer, offers integrated one-stop services including real-time quoting and online cargo tracking. We are funded by CNBM Group, a Fortune 500 enterprise and the largest G3000 Cast Iron firm in China.Hot Products
FAQ
- Gate valve DN65 what does that mean?
- Nominal diameter 65 gate valve.This depends on the material of your valve, it is new material, it is to use the outer diameter to do the standard, specifications with 63.75, and so on, because the new material is welded or coated with glue connection. So use the outside diameter as the standard, or the gap will appear.There is also the metal standard, according to the nominal diameter, or flange connection flange and skein skein are industry specifications.When it comes to the end, it must be between the pipe and fittings must be connected.
- What is plug welding gate valve?
- Socket welding valve refers to the use of socket welded connection valve.Simple socket welding is to insert the pipe into the gate joint to weld.The form of socket welding is mainly used for welding small bore valves and pipes, fittings and pipes. Small caliber pipeline wall thickness is thin, and error prone edge ablation, butt welding is difficult, more suitable for socket welding. In addition, the socket of socket welding has reinforcement effect, so it is also used under high pressure. But socketweld also has disadvantages, one is the stress condition is not good after welding, easy welding penetration, pipe inside a gap, so should not be used for piping system of crevice corrosion sensitive medium pipeline system and clean high requirements for socket welding. In addition, ultra high pressure pipeline, even small caliber pipe wall thickness is also very big, can use butt welding connection, as far as possible to avoid socket welding.
- About fire valve is gate valve or butterfly valve problems?
- Disease is generally in accordance with the design requirements, regardless of the butterfly or tie hair to meet the requirements, are two-way valve.
- Why does the centrifugal pump start and stop in the case of closing the gate valve?
- The centrifugal pump starts and stops in the case of closing the pump outlet valve. Start off the pump outlet valve is to reduce the starting current, stop when the pump is closed, the outlet valve is to reduce water hammer, prevent blade from bad.
- What gate DH10016, AM
- The first Z represents the gate valve (the initial consonant of the Chinese phonetic alphabet for the gate); the second 2 represents the drive mode of the valve, that is, electro hydraulic drive.
- What do you mean by gate valve type RVHX-0150-10 and Z45X-16Q?
- Z45x-16q, Z means gate valve, 4 means flange connection, 5 refers to dark rod gate valve, X means rubber seal, 16 refers to nominal pressure 1.6MpaRVHX means manual gate valve, 150 refers to the caliber of DN150, and 10 indicates nominal pressure of 1.0MPa
- What kind of copper gate valve copper content standards, there are no national standards?
- Please refer to: GB/T12225-2005 "general purpose valve, copper alloy casting technical specification" and GB/T 15116-1994 "die casting copper alloy"
- Why can't the pressure measuring point be set at the two ends of the gate valve when measuring the resistance loss of the gate valve?
- the valve before the pressure measuring point, distance of valve straight pipe length is 5 times the diameter of the valve after the pressure valve, the distance is 10 times the diameter of straight pipe length.