Dry Battries Related Searches
Dry Battries Supplier & Manufacturer from China
Okorder.com is a professional Dry Battries supplier & manufacturer, offers integrated one-stop services including real-time quoting and online cargo tracking. We are funded by CNBM Group, a Fortune 500 enterprise and the largest Dry Battries firm in China.
Light steel keel partitions and finished partitions
- Light steel: the frame and the outer panel should be in the construction site processing, but also brush at least 2 times the putty +2 paint.
Finished partition: mainly in the factory processing, in the field just assembled only.s
Light steel keel partition wall how to paint
- Partition wall painting method:
1, knock on the wall, listen to the sound to find the vertical keel (light steel vertical keel has 5cm width), and then thinner steel needle piercing, to confirm the location of the vertical bone. Select the length of 25mm or more dry wall nail into the load the weight of the whole painting, and then fixed on both sides of the gypsum board position on the balance of the line;
2, before doing the partition, you can consider in the predetermined location plus fine woodworking backplane for later use.s
House decoration, the designer said the wall with light steel keel good, but the construction told me that this low efficiency can only be maintained for 4,5 years so I do not know in the end listen to who
- Load on the best no problem with red brick, that wall how many square meters, if the area is less than 10 square meters can be brick 120 red brick walls
Do light steel keel gypsum board partition to pay attention to what matters?
- Gypsum board at the end of the seams should be open groove, easy to capping processing.
Gypsum board edge joints should be in accordance with the provisions of the process.s
Light steel keel wall can be installed sliding door
- How can not press ah. It is estimated that you are afraid of wood that you fooled you And your door is too big to shrink it. The normal door is 800. Get so much useless. Now the light steel keel wall is too much. How can we press the door.s
Gypsum board wall above the good paint glass?
- Gypsum board partition wall construction operation process:
(1) According to the design drawings, in the already done walls, floors, the ground release off the line, the door hole edge.
(2) according to the design drawings and the actual size, with a wheel cutting machine cutting keel and classified stacking.
(3) according to the line has been put away and the door edge, with nails or expansion bolts to the ground keel fixed on the ground floor, nail or expansion bolt spacing 600mm. The top of the keel into the wall of the reserved hole 100mm, and then use cement mortar packing fixed, or with nails, expansion bolts to the end of the handle along the top keel fixed to the wall.
(4) According to the cut line and the edge of the door, according to the size of the file size layout, painted in the edge, along the top keel, less than the modulus should be placed in the partition with the wall at the first board.
(5) According to the document mark will be cut in advance of the length of the vertical keel in turn inserted along the edge, along the top keel groove, the flange towards the direction of the proposed panel to be installed. Adjust the vertical, positioning accuracy, with rivets fixed. The vertical keel on the wall is fixed to the wall with a nail or expansion bolt, and the distance between the nail or the expansion bolt is 1m.
(6) the installation of doors and windows to strengthen the installation of the keel: the first installation of the hole on both sides of the vertical reinforcement keel, and then install the hole up and down to strengthen the keel, and finally install the big hole on both sides of the upper and lower reinforcement keel and bracing.
(7) Install the cross brace and support card. The vertical keel fastened, so that the entire partition keel has sufficient strength and stiffness.s
100 square light steel keel wall how many pieces of heaven and earth keel
- It depends on how high you need to partition the wall, if it is separated by 2 meters high wall, then up and down the world keel each need 50 meters. , If it is separated by 4 meters high wall, up and down the world keel each need 25 meters.s
100 light steel keel 9.5mm thick gypsum board double double-sided partition three times, three times latex paint.
- The following is the decomposition of the material (no loss), vertical wall keel spacing is generally @ 400, vertical keel is 2.5m / m2; along the top edge (heaven and earth) keel is 2/3 = 0.67m / m2; Piercing board is 4m2 / m2 partition wall area; large white putty is about 2.5kg / m2 partition wall area, latex paint is 0.5kg / m2 partition wall area. Brush twice to consider; the rest Is the card pieces, nails, bandages, white latex, high-strength nails and oblique support cable-stayed material (wood can be) and other auxiliary materials
Usually the wall should also have rock wool, 50 thick or 75 thicks
Basic working principle of automatic door
- How do automatic doors work, the basic composition of the automatic door machine is roughly the same, with more than one, and then with the door signal, you can configure a set of ...
how to lock sim card
- There are a lot of people asking how to unlock the SIM card,but few people ask "How to lock sim card?". How to lock sim card?Before answering this question, let's get...
Have you done your business with aluminium composite panel manufacturers
- Aluminium composite panel are usually used at building construction, houses, but also at some factories in this field. Have you ever heard of aluminium composite panel?Features of ...
what is basalt used for
- What are composite doors？Basalt is a kind of high-quality traffic building stone.Especially in the construction of highway, railway, port, airport runway,it is one of the best co...
how to install a door hinge
- In fact, we are not unfamiliar to the hinge.Cabinets, doors and other places usually use this stuff.But how to install a door hinge？ About the hinge,there are three different way...