Q:What are the requirements for buying an infusion chair and a medical waiting chair?

If it is a personal use, or private enterprises in small quantities custom-made, according to the strength of large engineering infusion chair manufacturers can. Don't look for small manufacturers.

Q:The bus station is getting what material?

Hello, the bus station and the airport chair chair, chair waiting for the train station, waiting for bank hospital chair, waiting chair is the same.

Q:Waiting chairs, stainless steel or iron?

Waiting chairs are mainly used indoors or outdoors, and iron waiting chairs are sure to rust if they are used outdoors. As for environmental protection, stainless steel is not easy to wear, never rust, strake is Aluminum Alloy strake, electrochemical treatment, the bottom beam is 2mm40*80mm steel pipe, spray paint outdoor powder, can withstand the wind and rain, sunshine test.

Q:What's the difference between a waiting chair and an office chair?

These two are completely different products and are hard to compare!Waiting chairs: for public places such as airports, stations, banks and so on, one person comes to six!

Q:What material does the station waiting for the chair use?

Hello, general bus station, train station waiting chairs are aluminum alloy, stainless steel as the main material, and some can install PU pad, so that the waiting chair more tall.

Q:The structure features of the Pu self skinning chair?

PU is polyurethane, referred to as polyurethane. PU has the following advantages:1., ozone resistance, aging resistance, mildew resistance, low temperature resistance, resistance to twists and turns;2., oil resistance: polyurethane elastomer is a strong polar polymer compound, and non-polar mineral oil compatibility is small, in fuel oil and mechanical oil almost no erosion;3., radiation resistance: Polyurethane resistance to high energy radiation performance is very good, in high radiation dose, still has satisfactory performance;4. under the same hardness, the bearing capacity of the elastomer is higher than that of other elastomers;

Q:What are the inspection standards for airport waiting chairs?

The height, width, depth and angle of the armrest should be reasonable, and the improper height of the handrail will lead to rapid fatigue of the shoulder. In addition to the height of the armrest, the width, depth, angle of the armrest pad. For example, when we read documents and newspapers, the arms that are placed on the armrests are usually slightly splayed outward for inverted material;

Q:What are the features of public waiting chairs? What are you looking for in public waiting chairs?

I don't think I'm overtired. The seat must meet the three degree curve of the human body, and the curved surface type chair seat can increase the contact between the bottom of the thigh and the buttocks and the seatThe area, which makes the pressure equally dispersed, does not focus on one point, and because of the slight inclination, it also stabilizes the pelvis and avoids sliding forward while sitting,Rounded seat design also reduces friction and contact on the inside of the knee joint and is beneficial to health. The fit of the chair, though it may workDifferent properties and different buy office chair, but most of the chair is not limited in use, so in the purchase, if the chair collocation is very high, is to buyThe greater the chance, for example, that the chair can be adjusted differently according to the movement of the user, because the user can not have only one sitting position, if LimitedDead, this chair is of no use. The chair can be tilted, and different office chairs will have different tilting areas, which can be roughly divided into the following:The back, seat and waist can be tilted; the back is tilted and the seat is not tilted; the front edge of the seat is fixed; the back of the seat is inclined to the back; the back and seat can be tilted; the backA tilt of five types, buyers can according to internal users of the different nature of the work to purchase, so the staff will greatly benefit the considerate.

Q:I want to make stainless steel furniture. What's the future? How can I open the market?

Stainless steel non-standard products custom made. Stainless steel operating platform, stainless steel monitoring console, stainless steel table and chair, stainless steel tool cabinet, console, stainless steel console and other power plant stainless steel office equipment.

Q:How comfortable is it to sit in a high back waiting chair?

This needs to be designed according to the man-machine style to satisfy the comfort. It seems that the comfortable feeling of SJ709 in Australia is very good.