WIRE DRAWING MACHINE FOR SS WIRE OR STEEL WIRE FACTORY

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
1 unit
Supply Capability:
500 unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:


 

1.Structure for Straight line wire drawing machine


This straight drawing machine is used for put wire into very thin wire ,form 7.0  ,8.0mm into 0.13mm etc 


 2. Features of sraight drawing machine 


1.this straight drawing machine is used for put wire into very thin wire ,form 7.0  ,8.0mm into 0.13mm etc 1. Drive: Host straight line wire drawing machine, the first five heads power by the AC frequency motor through high-frequency joint narrow V-belts, spread by the hardened reducer to capstan. And the other six heads power by the AC frequency motor through two high-frequency joint narrow V-belt to capstan.

 

2. Brake: Clamp brake mounted on the motor pulley, quick stop or emergency stop wire drawing machine, which can effectively brake. Its role not only as a brake, but also to prevent the reel reverse brake, release the clip close to the solenoid valve control clamp brake cylinder.

 

 

3. Capstan: The material is ZG45 steel, surface is build-up welded, the  surface is brightness, smooth, wear-resistant surfacing height of 150mm, long service life; hub height of 150-200mm.

 

4. Drawing die box: Die box is welded structure, into two cavity. The guide roller is mounted into the side to ensure that steel wire can straight into the drawing die, die holder should be adjusted to wire tangent to enter the drawing rolls tuning roller installed at the entry end of the mold base (2 # -11 # mode box) tuning roll by a small cylinder put power, tuning the swing of the roller, so that the corresponding sensor output signal to fine-tune the speed of change. Tuning roller wire tension by adjusting the air pressure change, regulation range 0.15-0.6Mpa. The mold box is also equipped with a stirring device. Tuning roller side of the mold box, a gear reducer single-phase capacitance running motor through a sprocket, power passed to the stirring arm to stir the mold box, lubrication powder, without agglomeration affect lubrication.

 

5. Jump-mode device: When drawn wire specifications total compression rate is less than the required 11 times drawing, can throw a drawing. Rejection mode principles: Inlet is small, outlet is fine, then dumped in front of passes; Inlet is big, outlet is rough, then throw behind the times. When the need dumped mold, the steel wire after the need to jump-mode machine mode box, and then into the next need to pull the mold box so that the wire can be within the effective stroke of the arm swing, thus ensuring the sensor can detect and adjust to match adjacent reel speed.

 

6. Capstan cooling: Inside of the capstan use narrow slit water cooling, cooling ring fixed in the body, capstan run through the spindle, when the water flow at high speed, during which water turbulence, and emitted from the narrow gap high-speed, high heat transfer efficiency, so that the rolls to cool; outside of the capstan use wind cooling by fan. Capstan tilt installation, increase the capstan product wire to extend the wire and the air heat exchange time.

 

7. Mold cooling: Drawing Die use open direct water-cooled, adjust the inlet valve to control the water height, when you need to replace the wire drawing dies, close the inlet valve, fast water emptying, and then change the mode, before and after the wire drawing dies, seals available copper pad or aluminum pad.


 3. Drawing machine images 

WIRE DRAWING MACHINE FOR SS WIRE OR STEEL WIRE FACTORY

WIRE DRAWING MACHINE FOR SS WIRE OR STEEL WIRE FACTORY

WIRE DRAWING MACHINE FOR SS WIRE OR STEEL WIRE FACTORY


4. Specification for drawing machine 
 

 

Items

Unit

LZ9-12/1200

LZ10/800

LZ9/700

LZ10/560

LZ10/400

Capstan diameter

mm

1200-900

800

700

560(600)

400(450)

Drawing dies

time

9-12

10

9

10

10

Max inlet diameter

mm

φ14-8

φ10-8

φ8-6.5

φ6.5-5.5

φ3.5-2.5

Min outlet diameter

mm

φ5-3

φ4-2.5

φ3-2.5

φ2-1.8

φ1.1-0.8

Drawing speed

m/min

300

360

480

720

840

Tensile strength

Mpa(max)

1300

1300

1300

1300

1300

Total compression rate

%

87.24-92.89

90.53-90.23

85.94-85.21

90.53-89.29

90.12

Average compression rate

%

20.45-19.58

21.00-20.75

19.58-19.13

21.00-20.02

20.50

Motor Power

Kw

110-90

90-55

75-55

37-22


5. FAQ


Whatstandard certificate we have ?

 We have business formation and  ISO9001:2008 standard and certificate.

Wgat's the scale fo rour factory ?

Number of employees: 100-200


 

 

 


 

 


 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range