Q:What brand of laser level is good? How much is the price?

A level instrument in which laser beams are used instead of manual readings. The laser beam emitted by the laser is introduced into the telescope cylinder to send a horizontal laser beam along the collimation axis. By means of the monochromatic nature and the coherence of laser, a piece of glass or a piece of metal with a certain shading pattern can be assembled in front of the telescope object lens, that is, the zone plate can cause diffraction interference. Through the telescope focusing, the focusing range zone plate, a bright and fine cross shaped or circular laser spot, thereby more accurate sighting target. If the photoelectric receiving target can be automatically tracked on the front and back level scales, leveling can be carried out. In the construction survey and assembly of large components, the laser level was used to establish the horizontal or horizontal lines in 1989.Digital level is the most advanced level, with a special bar level, through the instrument built-in digital imaging system, automatic level bar bar code readings, no manual reading is needed. This instrument can greatly reduce the labor intensity of Surveying and mapping work, avoid the subjective subjective reading error, and improve the measurement accuracy and efficiency

Q:What happens when the vertical level of laser level is tilted?

Take back to the factory maintenance, their own bad operation

Q:BOSCH low level instrument to see the comment, the line out too thick. Are there any other good brands to recommend?. There are so many brands on Taobao that they look dazzling.

DEWALT is acceptable

Q:Which brand of laser marking instrument (level instrument) is of good quality?

Changzhou laser marking equipment should be the best in China, but also the earliest in China, the largest production line marking instrument manufacturers.

Q:When the laser level is opened horizontally, it does not move on one line when it moves around. How can it be corrected?

The laser level adjustment in the horizontal center position, must take the center point adjustment in the center position, the more accurate and better. Don't think that we didn't ring eccentric alarm at certain position in the center, in fact is not necessarily is the center, but at a distance shorter than not more than 10 meters outside the basic can be a one-time success. The largest error is not more than 3 mm. When the flat side of the distance is beyond the scope of the provisions of the level; if the adjustment center at this time is not accurate so you need to first level line type as the base line to end then extended or moving position and the direction of the words: it is certainly to the connection is not at the same level error is large, so the level of the line side must not!

Q:How can the laser level adjust the height of the horizontal line?

You can fix the level on the three stand and adjust the height of the horizontal line by adjusting the height of the three leg.Laser level meter operation mode:When measuring, the working surface of the level instrument is close to the tested surface, and the reading can be carried out until the bubble is completely stationary.The graduation of the level is based on the slope value of one meter as long as the actual tilt of the length of L is calculated by the following: the actual slope = the value of the division *L*, the number of deviationsIn order to avoid the measurement error caused by the zero position of the level instrument, the zero level of the level instrument must be checked or adjusted before use.Level zero calibration method: the horizontal instrument is placed on the base of the stable and approximately horizontal plate (or machine tool guide rail). When the bubble is stable, the end is read at the end, such as the left end, and zero. Then turn the level of 180 degrees, still placed in the original position of the plate, to be stable after the bubble, still in the original one (left) readings A, the level of zero error is two points A grid. If the zero error exceeds the permissible range, then adjust the level zero adjusting mechanism (adjustment screw or nut, the error is reduced to zero within the allowable value. The nut shall not be turned freely for the screws which are not specified.

Q:Home decoration, heard by the laser level meter stick tile floor tiles more accurate and convenient, do not know which one to buy?

Yes, most workers use laser levels

Q:What are the common problems with infrared laser levels? How should I solve it?

Use note1, please do not disassemble the laser wire laying instrument2, use the instrument carefully to avoid heavy impact or violent vibration3. Do not use organic solution to wipe the machine4 、 the instrument is stored in a ventilated and dry environment

Q:Is laser level instrument harmful to human body?

Almost no, just don't look at your eyesThank you for reading my answer carefully. If my answer is helpful to you, please accept and evaluate the original and solve it

Q:I want to buy a laser level, I do not know is good or green, its principle is good, can see the horizontal line in the sun

To green, higher than 600, in the strong sunlight can only be sloppy