suitable for long distance connection
different material available
nominal torque Tn/n*m
D of axle
length of axle
- Q:What are the connecting forms of industrial pipe joints? Like buckling type connection,
- Working pressure of quick joint: 1.6Mpa. Temperature: -54 ~ 180 C. Working medium: gasoline, kerosene, heavy oil, hydraulic oil, fuel oil, frozen oil, water, salt, acid and alkaline liquid, high pressure gas etc.. Material: stainless steel, copper, Aluminum Alloy. Sealing material: NBR rubber, polyurethane, silicone.
- Q:Re series 24 degrees cone O ring seal pipe joint joint, corresponding to the national standard number is?
- There are many kinds of pipe joints, and the commonly used pipe joints can be divided into two kinds: hard pipe joint and hose joint. If in accordance with the connection pipe joints and pipe points, hard tube joint with flared type, sleeve type and welding type three, hose connector is mainly buckling type hose connector.In hydraulic system, the connection way of pipe and pipe joint is different. The screw is used to connect screw thread. The taper thread is screwed on its own vertebral body and is sealed with polytetrafluoroethylene and other substances. It is mainly used in the hydraulic system of medium and low pressure. The sealing effect of fine thread is very good, is often used in high pressure system, but it requires the use of combination washer or O ring to end closed, sometimes used copper gaskets, it is suitable for the pipe connecting pipe wall is thick, the main part of a joint body, and take over nut. When in use, the joint body is embedded in the target, and the end face is sealed by using the gasket mentioned in the front; the rubber seal is used between the joint body and the connecting pipe, and sometimes the spherical sealing method is adopted.
- Q:What are the sealing ways of pipe joints? Thank you
- Pipe joint seal: thread seal, cone seal, end face seal.There are several kinds of thread seal:Hemp - thick lacquer, this is the most traditional.
- Q:Outside the wire (wire) of what the standard joint size
- Structure and characteristics:The utility model relates to a sleeve type metal hose joint, which can connect a steel pipe without a thread and a hose, and can save the thread filling process, and only screws can be screwed in;The metal fittings are jacketed to connect the metal hose to the non threaded steel tube;Adaptation: steel thin steel wire pipe, black, tin pipe (water, gas);When choosing the ferrule type metal joint, please pay attention to the specification and size of the connecting pipe hose.Installation notesIn our daily life, we often see the pipe fittings on the pipe fittings. For this kind of products, we need effective installation to ensure that it can perform its functions better. Here is a brief discussion of a kind of pipe joint - card sleeve type joints in the installation of the use of methods.
- Q:Why are the sleeve joint leaks?
- The hardness of the clamping edge is not enough, or the steel pipe is too hard. After the assembly, the clamping edge can not cut into the pipe wall to form a seal. Solve: replace the qualified card sleeve.The end face of the steel pipe is not vertical or clean, which hinders the proper installation of the pipe. Solution: carefully clean the end face before installation.The joint body and the steel with different axis, leading to the assembly is not correct, extrusion is not tight, at this time can be found in the card set apart and cut the pipe wall, left the marks of a single whole foot ring groove. Solution: when installing, make sure the joint is coaxial with the steel symbol.
- Q:The material is 304 stainless steel 1/4 "NPT" threaded joint. How much MPa pressure can be received?
- The twenty-first page specifies the level of thread and material corresponding to the pressure application. Stainless steel thread used in the steam is 7 kg pressure (bar), the water temperature is above 105 degrees celsius. Other restrictions, standards.
- Q:What is a slot type mechanical joint?Copy search
- Because of the special sealing structure design of the rubber sealing ring and the clamp hoop, the groove connecting piece has good sealing property, and the sealing property is enhanced correspondingly with the increase of the fluid pressure in the pipe.
- Q:How tight is the gas pipe joint?
- For a fixed gas pipeline, it should be installed by a professional Gas Co, and the individual shall not change the sealing of the joint. It should be sealed by special sealant. Plastic pipes should not be too long, should be far away from the electrical circuit, and the high temperature area of the hearth.
- Q:What joints do nylon hard tubes work on?
- (two) clamp sleeve type pipe joint;Application: sealing pipe joint oil, water, gas and other non corrosive or corrosive medium, with plastic pipe specifications are flexible, and pipeline connection, has the characteristics of reliable connection, good sealing performance, so it is widely used in oil refining, chemical industry, light industry, textile, metallurgy, national defense, aviation, ship the system is suitable for all kinds of hydraulic transmission; mechanical engineering, machine tools and other equipment pipeline. Sleeve type pipe fittings manufacture standard following fifteen kinds:1, card sleeve end through pipe joint (GB/T 3733-2008)2, sleeve type cone thread straight pipe joint (GB/T 3734-2008)3, card sleeve type end through long pipe joint (GB/T 3735-2008)4, long taper pipe thread joint (GB/T 3736-2008)5, card sleeve straight through pipe joint (GB/T 3737-2008)
- Q:Hydraulic jointWho knows the hydraulic connection "3/8*25.4=9.525" refers to the connection?
- 3/8 is an English name. We call it "10 connectors", referring to the outer diameter of this joint.
We have established an excellent network with more than about 50 factories in this field. Our factories are specialized in different products in order to have a much deeper and more thorough knowledge of the market and be better prepared to cooperate with our customers.
1. Manufacturer Overview
|Annual Output Value
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||11% - 20%
|No.of Employees in Trade Department
|No. of Production Lines
|Product Price Range