Q:What is the difference between repeaters, routers, modems?

Repeater - as the name implies, for there will be a general signal relay, signal attenuation in the transmission process, serious attenuation will affect the normal communication, repeater can make signal "Rejuvination", but now it has been not much.The router is used for routing - like control network we send mail through the post office, each can be seen as a router, is based on the destination address you packet, the router to determine where to send.Modem is a device that converts digital signals into analog signals. In general, home phone lines are analog signal lines, our network signals are digital signals, we have to have a device for conversion, this device is a modem

Q:How can I use a wall mounted Poe modem / repeater?

The first wireless router:1. first login and broadband cat connection router.2. set the "SSID" and "channel" in the wireless settings - basic settings, and set the fixed channel number.3. set up the wireless signal encryption information in the wireless setting wireless security settings, record the SSID, channel and encryption settings information after the wireless router is set.

Q:Is wireless router directly plugged into the Internet?

Can enter the wireless router settings, run the setup wizard, select the "broadband Ethernet, obtain IP address automatically from the Internet service provider (IP), then the next step completed, while opening the wireless function, set the SSID, wireless security settings and restart the router encryption settings of your WiFi environment will have a wireless network you set the SSID, connect to the internet.

Q:Android phones do wireless relay, how can I do that?

If you do need to use mobile phone relay can, but need a mobile phone wireless module supports WDS function, which we call two WiFi wireless connectivity, a WiFi connection next door, when a hot to provide their own home. But mobile phones with this function are few and far from practical, because the cell phone's transmitting and receiving function is very small, and the battery power is also consuming rapidly.

Q:Which layer does the repeater run on the OSI model?

The repeater (REPEATER) repeater is the connection device above the network physical layer.

Q:After setting Repeater mode, the relay effect is not obvious or unsuccessful, what can I do?

In Repeater mode, the wireless signals, SSID, and encryption modes sent by TL-WR700N are exactly the same as those of the main AP, so after setting the Repeater, the wireless cannot search for the default TL-WR700N of the SSID. In the Bridge mode, the TL-WR700N can set its own SSID and encryption mode for wireless signals, which can be different from the main AP.TL-WR700N sets the Repeater mode as a relay amplification for the front-end wireless device, first establishing a wireless connection with the main AP, and then sending the wireless signals of the main AP,The TL-WR700N setting Bridge mode can also extend wireless coverage by first establishing a wireless connection with the main AP, then TL-WR700N sends its own wireless signals for client connections

Q:What network problems can a repeater solve?

To put it plainly, the two machines are very far apart. Only the cable will be connected. The signal will not be good, so you can use the repeater to connect each segment of the net within one hundred meters

Q:Can wireless routers be used as repeaters?

Can be used as a repeater.After entering the router management page, in the network parameter -LAN port settings, modify the IP and the main router is different. Restart after save.

Q:Why is the repeater full of signals, but not Internet access?

The wireless signal expander connected successfully after the mobile phone address bar will automatically pop-up extender login interface, need to set a password management extender. The password will be used to log the expander interface, the password is not connected to the Wi-Fi wireless password.4, enter the expander settings interface, extender will automatically scan the surrounding signal, wait a moment. In the list of scanned signals, find the signal you want to expand. Select the signal (if the search is not possible, the signal may be too weak, or for a Chinese signal, please modify the name of the extended signal).

Q:The repeater connects to the wireless network of the left neighbor's home, showing the wireless channel -1, and even the wireless network on the right side shows the wireless channel -6. What does that mean?

The channel does not mean the signal strength, but the current operating frequency of the wireless device.