Transfer and circulation of Acids, Alkalis, Molten Sulphur, Molten Lead and other Volatile Liquids in Chemical, Fertilizer, Process and other Allied industries.
- Q:I put down the motorcycle engine oil pump cleaning up after the cylinder head not to how oil ah
- Fill the oil pump with oil, and put it in it. You can't get the oil out of it
- Q:What parts of motorcycle oil pump are connected with them?
- Motorcycle structure is different, and parts connected to the oil pump is also different.1., two stroke engine small pedal (such as the old Mulan), the oil pump is connected with the engine rear axle.2., cross bike (such as SUZUKI GS125), the oil pump is connected with the oil pump gear, and rely on the installation of the crankshaft on the oil pump to drive gear drive.3. four stroke pedal (such as smart Qingqi 48QT Series), oil pump and oil pump gear is connected directly by the crankshaft drive (crankshaft and its processing gear)4. bending beam engine oil pump is connected with the oil pump drive rod, is driven by timing chain drive, oil pump sprocket, driven by the oil pump drive rod.These are some of the more common oil pump connection mode, because there are many types, it will not dwell here. Hope to be of help to you.
- Q:What is the cause of engine oil alarm?
- Oil lamp alarm reason::1, the amount of oil is insufficient, so that the pump oil pump volume reduced, or because of air into the pump does not oil, resulting in lower oil pressure;2, the engine temperature is too high, easy to make oil thinning, from a large gap in the gap between the resulting oil pressure drop;3, when the oil pump parts damage or wear, assembly and other problems arise when the gap is too large, will cause the oil pump out of oil or the failure of the oil shortage;4, the crankshaft and large, small tile gap between the improper, too tight will make the oil pressure rise, too loose will make the oil pressure lower;5, the oil filter and oil suction disc plug will also reduce the oil pressure;6, the oil return valve damage or failure: if the main oil return valve spring fatigue softening or improper adjustment, the valve seat and the ball with the surface wear or dirt stuck and closed, the oil return amount will increase obviously, oil pressure of the main oil channel also decreased;7, improper selection of oil: if you use the wrong or improper selection of grades, the engine will run when the oil viscosity is too low and increase the leakage, thereby reducing the oil pressure;8, the oil pipe in the oil leakage, plug phenomenon.Only normal oil pressure can ensure that the oil is sent to all the friction parts of the engine, too high or too low will affect the normal operation of the engine, and even cause damage to engine parts. So, when the alarm lamp should be immediately shut down to find out the reasons, troubleshooting before it can continue to work.
- Q:The oil pump is coming up. Why is the oil lamp still on?
- Check the oil pressure sensor
- Q:What is the driving oil pump of the car?
- The oil pump is driven by the power of the engine of the car.
- Q:How does the motor pump exhaust the air?
- The oil pump doesn't exhaust the air
- Q:Questions about the old Chery, the oil pump and the engine
- Bearing for a set or a low pressure, caused by many reasons, when you hold tile caused by the lack of oil, bearing should replace all, then replace the oil pump, oil lubrication is not good water temperature will be high, the fuel with the lights to replace the sensor
- Q:The oil pump is driven without a belt
- That should be sub models, and some rely on the chain, some directly crank pulley
- Q:How do you install the pedal motor pump?
- How to dismantle how old
- Q:6140 lathe oil pump, no fuel injection, what is the problem?
- The fuel pump is clogged,
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||51% - 60%
|No.of Employees in Trade Department
||Above 100,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range
||High and/or Average