Vehicle-mounted scissor platform
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
- Q:Can the stepping motor drive the hydraulic platform?
- Are you a driver for this motor? But the normal step motor is only for torque, step Angle, phase number, not for rotational speed; It may be a servo motor or torque motor, and if the speed is low it is the possibility of torque motors. In addition, you can measure the current, voltage or waveform below.
- Q:What is the phenomenon of the worker's transport of wood using a lift
- It's normal. This series of products for indoor type, widely used in star-rated hotels, such as the large supermarket industry lobbies, the aerial work inside the factory, has a balance, convenient operation, can enter the hall, can freely in and out of the elevator and less consumption, no pollution, work does not hurt the earth, can be used for wall and out work, work no dead Angle. The single column aluminum alloy electric elevator is fitted with the gantry cross attachment, which is suitable for the maintenance of movie theater, synagogue and church. The long door is easy to assemble, easy to operate, flexible to move, can span up to 1.1m fixed seat and other obstacles, and can stabilize the work on the step. High strength rectangular steel pipe making, rigid and stable. It is equipped with multi-wheel and flexible. Both ends can be adjusted, which can be used to cross different obstacles. The two sides are vertical adjustable, which can be used for the incline or step of a certain incline
- Q:Tomb raider 9 research base elevator to go to go to go to go to the order to pry the gear not to go down to go down to go down the card 3 to break up
- There are four of them, four of them. See the white climbing wall outside the elevator? Find a way to burst open a hole in the iron wire and climb to the fourth gear. There was no order in this gear, four of them were done, and the elevator fell down.
- Q:What are the elevating institutions
- The elevator is also called the elevating platform, which is a lifting device that lifts a person or cargo to a certain height. In the factory, the automatic warehouse logistics system such as vertical transportation, lifting platforms often also equipped with all kinds of plane conveyor equipment, as different height of conveyor line connection device.
- Q:Introduction of vertical elevator milling machine
- XD5032 X: milling word pinyin initials, on behalf of the milling machine D: should be on behalf of the manufacturer, 50: dalian is 32: vertical lifting platform structure is the most giant slalom spindle diameter of 320 mm
- Q:How to use the elevator to be safer and more efficient
- Constantly check the operation of the various agencies is normal, have no noise, if find fault, the elevator must be eliminated in time. 2, check the connection of the ministries, such as loose should be tight. When the compression of the connecting bolts should be in body check firmness, slightly shaft must have a split pin all connections, and to open fully. Always check all electrical wires and cables for damage. Make sure to cover and replace damaged parts in time. When the motor is overheat, stop the engine in time, and then keep running after the failure. The motor bearing lubrication is good.
- Q:What standard elevator platform needs to go to the special equipment inspection to report
- Hoisting machinery, it is to point to used for vertical lifting or vertical and horizontal moving heavy mechanical and electrical equipment, its range is rated lifting weight greater than or equal to 0.5 t elevator; The weight is greater than or equal to 1t, and the lifting height is greater than or equal to 2m crane and weight bearing form fixed electric gourd
- Q:To make a four trapezoid screw lifting up seven tons of lifting platform should be matched with the straight screw and motor
- Can be judged according to the accuracy requirement of lead screw grinding or rolling, depending on the load and its acceleration can choose servo power right away and screw the maximum load capacity (do longer engineers can intuitive judgment the diameter of the screw and large), so that you can around the power of the servo motor of the different speed and different lead screw to match, so there will be several different schemes: high speed servo motor with small lead screw (sometimes deceleration machine), big inertia servo with lead screw. Under the condition of the machine cost to determine, from two to three scheme choice, choice of method is to choose low cost, with high stability, cost effectiveness and cost are the same common and suppliers have a spot. If the single from choose the ways of the servo and screw usually have an intuition, like 3000 revolutions of servo goods on the market the most sufficient, screw is according to the supplier's inventory.
- Q:What about the heat treatment of the lifting platform?
- Servo feed system stability is the most basic condition to work, especially when low speed feed does not produce "crawl", and can adapt to the change of the external loads and does not produce resonance. Stability is related to system inertia, rigidity, damping and gain. The life of the feed system, is mainly refers to keep the transmission accuracy of nc machine tools and positioning accuracy of the length of time, namely the transmission parts's ability to maintain its original manufacturing precision, therefore, should be a reasonable choice material, heat treatment and machining process to the transmission parts, and adopt suitable lubrication method and protective measures, to prolong life.
- Q:How to automatically lift up and lift
- The motor is controlled by a time relay, the motor is driven by a change of speed, and when it falls in place, it meets the power failure of the limit motor
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Vehicle-mounted scissor platform
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
New products
Hot products
Related keywords