Q:I have put a new pressure valve and replaced both thermostat

If it is not overheating due to a stuck thermostat or bad heating element and you changed the TP valve then it is possible you have a problem with thermal expansion. When water is heated it expands and the more it is heated the more volume it will need to expand. Since the water heater and the piping are not designed to expand the water only has one place to go (well two if count the faucet) and that is out the TP valve. This problem is not uncommon and the solution is to have an expansion tank installed on the hot water heater in the piping near the tank.

Q:I need a valve cover gasket replacement because mine is leaking a tremendous amount of oil. The mechanic says it will cost about $269.00 plus tax. I wanted to make sure this figure was the average since I do not know a lot about cars. My car is a Mitsubishi Diamante 2001.

Hi Make sure your PVC valve it clear. That puts pressure inside the engine and makes the leaks. If it is plugged just tighten the valve covers might work.

Q:19 years ago i had a valve repair and now im due to have heart valve replacement. I heard that the metal valve make noise has anyone who has had the metal valve have this type f problem or any other problem with the metal valve it would be a great help if anyone could answer

tissue valve is better because you will need long term warfarin with metal one. metal ones have other drawbacks like amaemia too

Q:Butterfly valve general use occasions

Valve is especially suitable for low differential pressure, large diameter, large flow of gas and slurry liquid. For general control valve, DN300mm is big valve, only individual to DN450, and for the butterfly valve, DN500 below is a small valve, DN500 ~ 1000 is the standard valve, the largest butterfly caliber up to 9m. Visible, large diameter pipe with the main butterfly valve.

Q:Water supply pipe gate valve and butterfly valve which good?

1. gate valve: also known as gate valve or gate, there is a valve in the valve flow direction perpendicular to the medium, adjust the height of the gate, you can adjust the flow of fluid. Valve advantages are small resistance, close tight, no water hammer phenomenon, widely used in a variety of liquid and gas shut-off valve. It also has some adjustment function, but when the part is opened, the gate is easy to be wetted by the fluid. When the fluid flows, it causes the shaking of the alarm board and the sealing surface is easy to wear. The drawback of the gate valve is that the structure is complex, the price is more expensive, it is difficult to repair, and the solid material is easy to deposit in the valve seat groove. Therefore, it is not suitable for the pipeline containing fiber or solid material in the fluid. Commonly used in the air, steam, oil medium pipeline, but also used as vent valve and low silk system valve.Gate valve is commonly used as one of the cut-off valve, mainly used to connect or cut off the medium in the pipeline, not applicable to regulating medium flow. Valve is suitable for pressure, temperature and caliber range, especially for medium and large diameter pipes.

Q:Who can give me a download UG butterfly valve, needle valve, diaphragm valve standard model address, Japanese standard, American Standard.

Support many 3D CAD format, such as the commonly used UG, Pro/E, SolidWorks......As for the butterfly you said, don't post the link up, the standard JIS, American Standard ANSI, German standard DIN are.You use Baidu Search "LinkAble PARTcommunity", after the open registration, CAD format, such as UG, ASAHI and then to find the manufacturer home page, which is the valve, you said the Japanese standard, German standard, American Standard valve basically all.

Q:Butterfly valve in the use of the difference? Caliber?

Role of butterfly valveButterfly valve is to use disc type to open and close parts reciprocating reciprocating about 90 degrees to open, close or adjust the flow of medium valve. The butterfly valve has the advantages of simple structure, small volume, light weight, material consumption, installation of small size, the driving performance of torque is small, simple operation, rapid, high chemical corrosion, and can also have good flow control function and closure characteristics, the use of butterfly valve is very extensive. Its varieties and quantities are still expanding, and the development of high temperature, high pressure, large caliber, high sealing, long life, excellent regulation, as well as multi-function development of one valve. Its reliability and other performance indicators have reached a high level. Disadvantages, there is a certain resistance to the medium.Gate valves are more used in steam pipes and large diameter water supply pipelines, because of the general requirements of fluid resistance is small, the use of gate valve.Valve is hand wheel rotation, stem upward movement. Flow is not the same, the gate valve requires full open. Need a higher installation space, the valve sealing surface has a certain self sealing capacity, its spool by the media pressure closely with the valve seat sealing surface contact, to achieve tight leakage. Wedge gate valve spool angle is generally 3~6 degrees, when forced to shut down excessive or temperature changes of the valve core is easy to die. Therefore, high temperature and high pressure wedge gate valve, in the structure have taken certain measures to prevent spool stuck. The valve in the opening and closing valve and valve seat sealing surface contact and mutual friction is always so easy to wear sealing surface, especially in close off the valve, the valve before and after the great pressure, sealing surface wear is more serious.

Q:How big is the butterfly valve with a diameter of 80?

Generally speaking, especially small caliber, the butterfly valve will not use the variable diameter. Therefore, the butterfly valve DN and pound class selection, according to the field pipeline flange DN and pound level.So, in a strict sense, the caliber of the butterfly valve and the diameter of the pipe have not much relationship.Specific to your pipe diameter, there are questions: 80 diameter refers to the outer diameter or inside diameter? Yes, there is no flange on the site. Do you need a pair of flanges to be supplied?

Q:Do you use the straight stem butterfly valve in the fire fighting engineering?

Bar valve bar, did not hear the bar with butterfly valve, ah, there are pairs of folder and hand wheel type bar

Q:What type of butterfly valves do you have in DN125?

125D42X: manual double eccentric flange butterfly valve 125D3 (6, 9) 42X: worm (gas, electricity) double eccentric flange butterfly valve125D41X: manual single eccentric flange butterfly valve 125D3 (6, 9) 41X: worm (gas, electricity) moving single eccentric flange butterfly valve125D43H: manual three eccentric flange butterfly valve (hard seal)125D3 (6, 9) 43H: worm (gas, electricity) move three eccentric flange butterfly valve (hard seal)125D71X manual alignment type butterfly valve125D3 (6, 9) 71X worm (gas, electricity) midline type clip butterfly valve125D3 (6, 9) 73H, worm (gas, electricity) three eccentric pair clip butterfly valve (hard seal)125BD71 (F4) X corrosion resisting fluorine (wrapped) pair clip butterfly valve