Q:How does the pneumatic butterfly valve control the angle of opening?

The angle of the rotating shaft is controlled so that the angle of the butterfly valve is controlled. You just have a good electrical locator

Q:Butterfly valve D71X-16 and D71X-16Q what is the difference?

The two difference is that the body of the material is not the same, 16 behind with no sign, expressed as a default, is carbon steel (usually C), if you need to specify material, just behind with symbols, such as Q nodular cast iron, stainless steel P.

Q:The difference between butterfly valve d71x_10s and d341s-10

Before distinguishing between the two, you must first read the identification of the valve type:D stands for butterfly valves,3 means that the worm gear is connected and the drive does not indicate the handle7 and 4 indicate pipe to clamp connection, pipe flange connection, respectively1 means single eccentric, that is, the stem is not in the center of the butterfly plateThe former S indicates the material name of the valve body - plastic, X means sealing and the lining material is rubberThe latter S indicates the sealing lining material code ---- plastic, and the valve body is cast iron.10 means stress.

Q:Butterfly valve model D373F-16C, ask God answers

D butterfly valve, 3 turbo rotating, 7 pairs clip type, 3 eccentric F PTFE seal, 16 nominal pressure 1.6MPA, C valve body material, carbon steel

Q:What kinds of butterfly valves are available? What is the working principle of butterfly valves?

According to the form of sealing:(1) forced sealing butterfly valve.1) elastic sealing butterfly valve. The pressure of the valve seat, seat, or plate is produced when the seal is closed by the pressure from the valve.2) additional torque seal butterfly valve. The seal is produced by a torque that is applied to the valve shaft.(2) pressure sealed butterfly valve. The pressure is greater than the pressure on the seat or plate.(3) automatic sealing butterfly valve. The pressure of the seal is automatically generated by the pressure of the medium.Divided by work pressure:(1) vacuum butterfly valve. Working pressure is lower than the standard atmospheric pressure butterfly valve.(2) low pressure butterfly valve. Butterfly valve with nominal pressure PN<1.6MPa.(3) medium pressure butterfly valve. Butterfly valve with nominal pressure PN 2.5--6.4MPa.(4) high pressure butterfly valve. Nominal pressure PN is 10. 0--80.0MPa butterfly valve.(5) ultra high pressure butterfly valve. Butterfly valve with nominal pressure PN>100MPa.

Q:I have a good set of #142 Pontiac heads with small diameter valves. I want to have the heads enlarged to accept the larger Pontiac valves, and I have the larger exhaust valves out of #13 heads and the larger intakes from 6X8 heads. The valves appear ok and shiny on the stems

Roll the valves by the stems on a perfectly flat table. If there is no wobble, your valves are most likely not bent. Take them to a machine shop and have them checked for imperfections and reground and they'll be good as new.

Q:The water supply pipe is the gate valve And on the cross dry pipe are the gate valve? To answer the 30

I suggest you find out the pressure and installation position first, the condition allows, you can choose butterfly, after all, much cheaper than butterfly valve. After the completion of the project, will be mainly engaged in the acceptance of problems, there are special management of fire units.

Q:The difference between the electric control valve and the electric butterfly valve, respectively, the application situation

Butterfly valve switching speed, fluid resistance is small, but the flow control is not good, suitable for only fast opening and closing occasions. Control valve switching speed is relatively slow, fluid resistance, but the flow control of the linear good, suitable for flow control requirements of the occasion.

Q:How big is the butterfly valve with a diameter of 80?

With the 80 caliber butterfly valve.Also known as butterfly valve, control valve has a simple structure, can be used for low pressure pipeline valve switching control is closed parts (disc or disc) is a disk, around the valve axis to achieve the opening and closing a valve, the valve can be used to control the flow of air, water, steam steam, all kinds of corrosive medium, mud, oil, metals and radioactive liquid media and other types of fluid.

Q:My bike has now 6200 miles on the odometer. The manual says that a valve adjustment should be performed every 6000 miles. But the bike runs fine. Can I just have the valve checked or should I have them adjusted even though the bike is fine? What will happen if I just keep riding it?

In reality, lots of bikes go their entire lives without a valve adjustment. In my opinion that is a great way to ruin a bike though. They have a maintence schedule for a reason. If a valve isn't seating, it can hurt performance and the valve will not be able to transfer heat to the head. That can burn a valve and cause detonation. You have to check valves to adjust them, and the labor for just checking will be nearly the same or identical to doing the adjustments. I do all my own wrenching, so money isn't really an issue, but if I were you, I would just bite the bullet and take it in.