Q:Butterfly valve D71X-1.6C, DN50, there is no difference between C and no C? What do you mean by "concrete"?

The C indicates that the material is carbon steel and does not indicate cast iron (generally omitted)

Q:Does the wet alarm valve group need to install the signal butterfly valve?

The wet alarm valve group shall be equipped with signal butterfly valve.The signal butterfly valve is generally installed in two parts: floor level, dry pipe, flow indicator front end, trunk pipe, wet alarm valve, front end.Floor level pipe installation is a function of the signal valve, when the floor spraying system needs repair, close the valve, open the end of the floor drain, emptying the water in the spray system, maintenance;

Q:When i waa replacing the valves in the las 4 valves , they dropped and i dont know how to make them go back up, and i dont want to take the engine out of the car, is there any tool to make the valve go back up or there is any way to do it?? People told me that i can crank it by and , but i dont know how to do it where do i have to do it, i need help please im begging for help!

Engine dis-assembly is now required .

Q:Butterfly valves are widely used in 2.0MPa below the pressure and temperature of not more than 200 degrees of various media, right?

3. kinds of butterfly valve:According to the connection mode: flange type, clip type.According to the material of sealing surface, soft seal and hard sealing.According to the structural form, butterfly valves can be divided into the following types:Plate typeInclined plate typeOffset plateLever type4. butterfly valve features:(1) the structure is simple and the shape is small. The utility model has the advantages of compact structure, short structural length, small size and light weight, and is suitable for large caliber valves.(2) the resistance of the fluid is small, and when the valve is fully opened, the valve seat passage has an effective circulation area, so the fluid resistance is smaller.(3) open and close, convenient and quick, good adjustment performance, butterfly plate rotation 90 degrees can be completed headstock. By changing the angle of rotation of the disc, the flow can be graded.(4) the opening and closing moment is smaller, because the butterfly plate on both sides of the rotating shaft is basically equal to the medium, and the opposite direction of the torque is generated, so that the opening and closing is more labor-saving.(5) low pressure sealing performance, sealing surface materials generally use rubber, plastic, sealing performance is good. Limited by the material of the sealing ring, the pressure and the temperature range of the butterfly valve are smaller. But the use of hard sealing butterfly valve pressure and temperature range has been greatly improved.

Q:How do you explain A in butterfly valve D37A1?

Represents a seal or lining material symbol.Said sealing ring or lining material with the Chinese phonetic alphabet: B Babbitts D nitrided steel, acid resistant stainless steel H, J L Aluminum Alloy, hard rubber, nylon NL, P leather, SA PTFE, SC PVC, SD bakelite, T copper, TC enamel, X rubber, Y hard alloy

Q:Butterfly valve is generally used in what position?

Butterfly valve used in furnace, coal gas, natural gas, liquefied petroleum gas, city gas, hot and cold air, environmental protection, chemical smelting and power building water supply and drainage engineering system in conveying a variety of corrosive and non corrosive media pipeline, used to adjust and cut off the media flow. It can also be used for switch control of low pressure pipeline medium.

Q:What's the difference between a clip type turbine butterfly valve and a flanged turbine butterfly valve?

For clip butterfly valves, there are no flanges at the ends of the butterfly valve. There are only a few guide bolts. The valve is connected with the end flange with a set of bolts / nuts.In contrast, the demolition to facilitate some of the lower cost of the valve, but the drawback is that a sealing surface problems, the two sealing surfaces have to be taken apart.Flange butterfly valve at both ends of the flange, and pipe flange connection. The seal is relatively more reliable, but the valve is of relatively high cost.

Q:What's the difference between D71X-16 and D71H-16 butterfly valves?

First, model D71X model means that, on behalf of 7 representative D butterfly valve, butterfly valve connection form for clamp connections, 1 straight, X represents the seal in the form of soft sealing, the sealing surface usually NBR H metal seal is usually 2Cr13 16 represents the pressure of 16 kg pressure weldingJin Ya valve is the production of hard sealing butterfly valve or soft sealing butterfly valve line leader, what problems can ask their units, technicians will answer for you

Q:Butterfly D371X5-16ZB1 what does each letter stand for?

Daily valve pressThe regular model is out of step with you. I can only explain the regularD371X5-16ZB1D is butterfly valve3 is the turbine drive7 is the clamp connection1 is the display opening signX is a rubber seal16 is 16 kg pressureI don't know the other superfluous letters

Q:What are the functions and uses of butterfly valves?

Industrial butterfly valve features, capable of high temperature, applicable pressure range is higher, the valve nominal diameter is large, the valve made of carbon steel, the valve plate sealing ring using metal rings instead of rubber rings. Large high temperature butterfly valve welded by steel plate, mainly used for high temperature smoke duct and gas pipe.Construction: mainly composed of valve body, valve stem, disc and sealing ring. The valve body is cylindrical and has short axial length and is internally provided with a plate.