Packaging & Delivery of Valve Body Manufacture
Packaging Details: wooden case/as per the customer
Delivery Detail: TBD
Specifications of Valve Body Manufacture
2.Good quality and price
4.Drawing are welcome
gate valve for oilfield exploiting valve manifold
nb: 2 1/16-4-1/16 slab gate valve
wp: 2k-20k psi oilfield exploiting gate valve
payment : TT as per normal practice
- Q:Machining process analysis of typical ball valve parts
- 4 easy operation, open and close rapidly, from fully open to fully closed as long as 90 degree rotation, facilitate remote control.5., maintenance is convenient, ball valve structure is simple, the sealing ring is generally active, disassembly and replacement are more convenient.6. in full open or full closed, the ball and valve seat sealing surface and dielectric isolation, the media through, it will not cause erosion of the valve sealing surface.7., a wide range of applications, from small diameter to a few millimeters, large to several meters, from high vacuum, high pressure can be applied.
- Q:Does the big casting valve body do radiographic inspection?
- See general valves used in site is important, take what kind of medium.150 pounds of pressure is low, estimated to be not what important parts, generally do not need to do testing, the testing cost is not low.
- Q:What is the sealing ring on the valve body?
- Those two types of 0 ring sizes are not very good, one of the interference is too large, one is too small. When the interference is large, it is easy to scrape the sealing ring. When the interference is small, the pressure will not be sealed. ,
- Q:What's the function of the valve inside the car's automatic transmission?
- Working principle of hydraulic torque converterAt present, the single stage, double phase and three element locking type hydraulic torque converter is widely used in the car, consisting of pump wheels, turbine and guide wheel. The pump wheels and turbines are in pots. With the pump wheel torque converter shell is connected as a whole, active element; turbine suspension in the torque converter, connected by spline and the output shaft is a driven element; guide wheel is suspended between the pump and turbine wheel through a one-way clutch and a guide wheel shaft sleeve is fixed on the transmission housing.When starting the engine, the crankshaft drives the pump wheel rotation, because of the centrifugal force generated by the rotation of the working liquid pump wheel between the leaves along the blade from the inner edge to the margin thrown out; speed of this part of the work fluid has both rotate with the pump wheel park circumferential and axial, rushed to the turbine speed. The working fluid impacts the turbine blades and pushes the turbine to rotate in the same direction as the pump wheels.
- Q:How much is the Passat 1.8T transmission case?
- Hello, replace the valve body, the price is relatively high, the car's transmission valve can be maintained, the specific gear box failure, you can contact our master specific instructions.
- Q:Lang Yi double clutch body oil how to add?
- Lavida seven speed dual clutch is normal maintenance is not needed if you need to change, only need to replace the gearbox oil transmission below the oil discharge screw down the transmission out, then from the air hole transmission above two liters double clutch automatic transmission oil can.
- Q:Is the valve flow characteristic determined by the actuator or the valve body?
- Valve flow characteristics are the characteristics of the flow rate of the flow through the valve when the fluid is set at a constant pressure through the valve closed to the full opening. Therefore, the spool form is determined, and the actuator is a driving device for them in any form it is driven by the valve fully closed to fully open position change.
- Q:Gas stove body and fire burning a plate at the bottom of Never mind
- No, the fire is burning fire plate plate at the bottom of the high-temperature deformation caused by.
- Q:How to dismantle Octavia Skoda body
- Hello friend！ This requires special tools! If not, it may break the two clutch pumps! There's something wrong with the car. Ask the car master. 4S shop professional technicians, 10 minutes to solve. ]
- Q:What is the working principle of electro-hydraulic proportional relief valve, what is the sign of valve body?
- The driving voltage of the valve is generally 0 to 10V has a special drive circuit board through different voltage given to change the overflow resistance to flexibly change the system flow, cross-sectional area is constant speed following changes to the role of regulationBody symbol Baidu search electromagnetic proportional relief valve on the line
We have excellent specialist and technical level constructors and technicians, experienced production workers and the most modern production machinery and equipment. Products: forging rings, slewing rings, wind power gearing rings, flanges, equipment flanges, cylinder flanges, hydrogenation cylinders, roll sheets, forged adapters, connecting flanges, valve body, gear wheels, and others carbon steel, alloy steel, stainless steel forged parts.
1. Manufacturer Overview
|Annual Output Value
||US$50 Million - US$100 Million
||30.00% North America
30.00% Western Europe
10.00% Mid East
10.00% Eastern Europe
10.00% Northern Europe
||ISO 9001:2008;DNV;BV;ABS;GL;RINA;LR; KR; NK;CCS;CE;
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||21% - 30%
|No.of Employees in Trade Department
||50,000-100,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered
|Product Price Range
||Low and/or Average