Unique Design Temperature Control Colour Changing Led Bath Faucets Zinc Alloy Handle Basin Mixer
- Loading Port:
- Shenzhen
- Payment Terms:
- TT
- Min Order Qty:
- 200Pcs PCS
- Supply Capability:
- 1000Pcs Per Month PCS/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Product Description:brass body with Zinc alloy handle,Ceramic cartridge,Chromium plated:0.25um, Nickel plated:8um,with two 60CM flex hoses & fastening piece, hydropower, LED color changes with water temperature
Carton Size:63*47.5*37.5cm
About Product:1.Built-in LED light.
2. LED Power Source: a)4*1.5V AA batteries voltage supply, low power consumption; b)"by water flow, described as "hydropower" in the Specification.
3.LED color: Red, Green, Blue.
4. All necessary installation accessories included.
5.Built-In durable ceramic valves ensure no water leakage.
6.Laboratory tested for up to 600,000 life cycles at 90 degrees.
7.Laboratory tested to withstand high water pressure of 1.7MPA.
8. 2 years warranty.
- Q:I'm changing from a white sink to a SS kitchen sink. The faucet is shiny chrome. The sink has more of a dull brushed finish. Should I get a new faucet or do you think it will look fine? Any answers appreciated, especially if you have done this yourself! :)
- Chrome looks good with any sink. Matte finish hides water mineral spots, but, doesn't look as clean.
- Q:Most of the answers i got on the last question were not the answers i was looking for. Most answers weren't telling me whether this will for OR whether i need my landlord to buy a different kind of faucet.I need to know if this faucet will fit this OUT DATED sink? My landlord bought it for me. It's a one handle faucet, so is the old one.
- yes and you need a BASIN WRENCH !
- Q:Master bedroom washbasin faucet how to install the washing machine tube
- In the faucet below the water at the three links, and then split out a washing machine
- Q:How to change the faucet of the washbasin?
- Will need to change the direction of the faucet wrapped around the raw material with about 15 laps, not too much but not too little, according to the actual situation may be. Align the wire to tighten, pay attention to when the twist some difficult when it is twisted it is not twisted, for the next good demolition. Open the total water valve on it, if you see the leak at the connection can be twisted in a circle can be, or remove the plus raw material belt.
- Q:how can i change the kitchen faucet and sprayer?
- 'Wired has it right, but forgot: Measure the 'hole pattern' in your existing sink/countertop and be sure that the replacement you buy has the same pattern. There are different numbers and spacings of those holes. It's maybe a two hour job for an experienced plumber. You should be able to do it in less than a day.
- Q:What a huge headache it looks like.The rubber seal on my small bathroom sink faucet is leaking just a little bit (not bad). As I look underneath the sink cabinet, the faucet mechanism is way in the back of the sink basin and very hard to get to. Need plumber and they are super expensive. No way I can do this by myself, I do not have the tools for one.Looks like the whole sink apparatus has to come out to get to the underneath portion of the faucet.How much do you guess this will cost? Just to replace this rubber seal that will probabl cost $1.00.Thanks.
- You can get the ring from any hardware store. However I recommend you just buy a variety pack with 10-20 different sizes. That will save you many trips back to the hardware store if one doesn't fit. Also check with friends to see if anyone has a couple of pipe wrenches you can borrow.
- Q:We found an older (maybe 10-15 years) cast iron sink that is 48 inches long with two large basins and a small one in a junk trailer. It has 6 faucet holes drilled like this 0 0 0 on the back and we were wondering what all the holes 0 0 0 were for.
- All I can think of is 3 for the faucet and hot and cold taps, one for a sprayer maybe, another for a soap dispenser maybe and the last one for filtered water. That's my guess anyway.
- Q:hey guys, im replacing a kitchen faucet for my mom right now, and Its not one of the ones where it scres in on the two side panels, it has a long threaded neck that attatches to the sink basin, how would I take this out, I tried spinning the faucet to just unscrew the threading but it pivots...
- Faucets that I'm familiar with sit on top of the sink and are bolted down below the sink. You have to loosen nuts under the sink from the threaded water supply lines on the bottom of the faucet unit, then lift the entire unit out from the sink. That leaves holes in the sink. Threaded water supply lines on the bottom of the faucet fit through those holes and water lines from your house's water supply are attached to those. But the handles, neck, the whole shooting match is one unit.
- Q:The bathroom put a washing machine, bought a three-way dual-switch faucet, had wanted to install in the basin to connect the faucet on the angle of the valve, the result because the bathroom cabinet
- Oh, no worries! Because the current purchase of the toilet tank is just a high water design, so the water after the water tank will not return to the washing machine, and the main water pipe generally maintain 3 kg pressure, the toilet water tank in the water Water level, only the water will not return, tap water is a disinfection of sterile powder, you are not worried.
- Q:want to change the faucet of the wash basin, ask the steps. There are pictures
- The faucet is connected to two hoses, which are received from your home's water pipe and the main valve is closed and the hose is removed
1. Manufacturer Overview |
|
---|---|
Location | Kaiping,Guangdong |
Year Established | 2004 |
Annual Output Value | Above RMB5 Million |
Main Markets | Europe and the United States, Australia |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | Guangzhou |
Export Percentage | |
No.of Employees in Trade Department | 4 People |
Language Spoken: | English;Chinese; |
b)Factory Information | |
Factory Size: | Above 3000 square meters |
No. of Production Lines | 2 |
Contract Manufacturing | OEM Service Offered;Design Service Offered |
Product Price Range | Average |
Send your message to us
Unique Design Temperature Control Colour Changing Led Bath Faucets Zinc Alloy Handle Basin Mixer
- Loading Port:
- Shenzhen
- Payment Terms:
- TT
- Min Order Qty:
- 200Pcs PCS
- Supply Capability:
- 1000Pcs Per Month PCS/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords