Unique Design Temperature Control Colour Changing Led Bath Faucets Water Power Basin Mixer

Ref Price:
$61.32 / pcs
Loading Port:
Shenzhen
Payment Terms:
TT
Min Order Qty:
200Pcs PCS
Supply Capability:
1000Pcs Per Month PCS/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Product Description:brass body  with Zinc alloy handle,Ceramic cartridge, Chromium plated:0.25um, Nickel plated:8um, hydropower, LED color changes with water temperature

Carton Size:71*35.5*31.5cm

About Product:1.Built-in LED light.

2. LED Power Source: a)4*1.5V AA batteries voltage supply, low power consumption; b)"by water flow, described as "hydropower" in the Specification.

3.LED color: Red, Green, Blue.

4. All necessary installation accessories included.

5.Built-In durable ceramic valves ensure no water leakage.

6.Laboratory tested for up to 600,000 life cycles at 90 degrees.

7.Laboratory tested to withstand high water pressure of 1.7MPA.

8. 2 years warranty.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Plumbing Question..Moen Faucet?
unhook all the plumbing fron underneath. Take the whole sink off the vanity and tackle it that way. It is pretty tough sometimes to get the necessary leverage when trying to access everything from underneath. Might be a bit more labor intensive but it will certainly save you some busted knuckles and bruises on your head.
Q:How do I replace my kitchen faucet?
There are different styles of faucet. There may be one projection or three (or four.) You would have to go back a very long way for the thing to be screwed down from the top. Usually there is from one to four "nuts" that hold the faucet down to the sink top. You are going to have to crawl under the sink to see and loosen them. It is an good place to start anyway as you are going to have to see if you can turn the water off under the sink or have to turn the house off instead. Once the water is turned off, disconnect the supply tubes and then loosen the nuts and remove the faucet from above. Most of the modern nuts are plastic but older ones may be rusted and difficult to remove. Sometimes a basin wrench can help and at least once I had to cut the faucet off with a sawzaw after removing the countertop.
Q:Basin double hole faucet outlet pipe bottom leakage how to do?
The middle of the pipe has been demolished to pull down on the line. Inside the o-ring is broken, the hardware store can not buy that circle, to go to a special industrial market to buy things is not expensive dime. If you do not ask that the outlet pipe, then use the raw material with more than a few laps to install and do not leak
Q:How to remove the basin faucet filter
The head of the water end of the filter cap hat down, you can pour out.
Q:hot water faucet in bathtub makes thump noise and stops running?
Sound like you have a bad anti-scald valve. Generally you need to replace the entire tub/shower valve, but some manufactures design theirs with a replaceble anti-scald unit.
Q:What is the size of the faucet?
In addition, if you need to install their own, it is recommended to buy a faucet when the "raw material" (also called "raw tape"), when installed in the screw on the mouth to prevent leakage.
Q:What is the material for the basin faucet? Please know that friends talk to see.
Basin faucet must be pure copper, the market is some of the leading alloy, the damage to the human body is still great. Another point is to buy the brand of basin faucet, such as: nine animal husbandry, in the special, special pottery, the brand's tap quality will be guaranteed, these brands you may wish to consider the next.
Q:How to clean severe yellowing from underneath the bathroom faucet assembly?
Chances are its from the pipe dope or plumbers putty that was used. Treat it like a greasy stain and use some baking soda, some cleaner like Greased Lightening or Blue Wolf. You can also try putting some hydrogen peroxide on it over night and covered with a rag or some plastic if its not granite or marble. Should clean up fine then. Good luck!
Q:Do I need to turn the water off to my house to replace my kitchen faucet?
before doing any thing try cleaning the filter at the spout. at the end of your fauset spout there is a screen. sometimes theres as many as 3 screens stacked one on top of the other. twist off the end counter clockwise and see if they are plugged. if so just clean them and put them back and walla new faucet. if it does need replaced though, all you needto do is turn the 2 water valves off under your sink. not the main water supply. some faucets can be a bear if you haven't done it before. you might need a basin wrench for the nuts if there isn't enough room for a cresent wrench. good luck.
Q:The nuts that hold my kitchen faucet in place are too tight but not rusty Need help unscrewing them. Advice?
I'd have to assume you're referring to the pot metal hex nuts that hold the faucet assembly down in the sink, or possibly the newer plastic nuts, which can sometimes be so tight that it seems nearly impossible to remove them. If the nuts are metal, I'm sort of with Ed, in that I use a Dremel tool with a cutting wheel attachment to cut the nut. You're probably not going to reuse the faucet assembly so it doesn't matter if you mess up the threads on the bolts or threaded pipes hanging down under the sink. The Dremel tool is small enough to get it up into fairly tight areas and with a little care you can cut the nuts in two and then knock them loose with a small punch and hammer. If the nuts are the plastic ones with the four fins sticking up, I made a tool out a piece of 1" galv. pipe, by cutting a couple of slots in a cross formation on top with a hacksaw, that fits right over the fins and can be turned with either a small screwdriver, (if you drill a hole through the bottom end of the pipe), or with a pair of channel locks, by grabbing on to the pipe itself. Just use safety glasses while working under a sink to protect your eyes.
We are very popular with consummate skill, advanced workmanship, perfect after sales service in the world. From now on, our company devotes ourselves to enterprise construction and development, market is the guide, management is the basis, science is power.

1. Manufacturer Overview

Location Kaiping,Guangdong
Year Established 2004
Annual Output Value Above RMB5 Million
Main Markets
Europe and the United States, Australia

Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Guangzhou
Export Percentage
No.of Employees in Trade Department 4 People
Language Spoken: English;Chinese;
b)Factory Information  
Factory Size: Above 3000 square meters
No. of Production Lines 2
Contract Manufacturing OEM Service Offered;Design Service Offered
Product Price Range Average