T5 LED Tube SMD Chip High Efficiency 1.2M 13W

Ref Price:
$6.86 / pc
Loading Port:
Shenzhen
Payment Terms:
TT
Min Order Qty:
10 Pcs pc
Supply Capability:
100000 Pcs Per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

T5 LED Tube SMD Chip High Efficiency 1.2M 13W 1. This product meets the standard of CE certification.
2. With internal No-isolated power supply.
3. Round and the elliptical tube are available.
4. Use the most mature international well-known LEDSMD2838 as the light source, which can ensure the led tub35 as the light source, which can ensure the led tube brightness and long lifetime, also can reduce the light decay.
5. Use the high quality aluminum PCB for LED’s better heat dissipation.
6. High-grade PC cover with nice light transmittance(> 95%),Transparent PC cover and frosted PC cover are available.
7. 180 degrees beam angle makes the lighting effect better.
8. CRI(standard products)>70,it can be over 80 if required.
9. Ambient temperature:-20°C-40°C, surface temperature: 42°C-45°C
10. No mercury, lead or other hazardous materials; no radiation, no electromagnetic radiation, no frequency flash, instant start up, no hurting eyes.
Applications:
Replacement for conventional fluorescent tubes:
1. Hotels
2. Conference/ meeting room
3. Commercial Complexes
4. Residential/ Institution Buildings
5. Schools, colleges & Universities
6. Hospitals General li

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How do I get the four joints of the LED fluorescent tube
I can't put a picture on it, you can try it yourself, add a rectification bridge at each end of the tube, and then you put the positive plus positive on both sides, negative plus negative, onto the next bridge
Q:What about the normal daylight tubes replaced with LED tubes, ballast and flashers?
The rectifier usually has two types of inductance and electronic type: the direct short answer of inductance (one to one). The wire and the zero line of the electronic type (two in four) are short connected to the corresponding two sets of two lines, the regenerator is pulled directly, and the LED tube is installed.
Q:The notice of LED daylight lamp tube
Eight major advantages: 1, the environmental protection lamps and lanterns, protect the earth the traditional fluorescent lamp contains large amounts of mercury vapor, if broken mercury vapor will evaporate into the atmosphere. But leds don't use mercury at all, and leds don't contain lead, which protects the environment. LED fluorescent lights are recognized as the green light of the 21st century. 2, high efficiency conversion, reduce fever Traditional lamps and lanterns will produce large amounts of heat energy, and the LED lamps and lanterns is all the electric energy into light energy, not cause waste of energy. And for documents, clothing doesn't have a fading. 3, be quiet and comfortable, no noisy LED lamps and lanterns will not produce the noise, for the occasion of using precision electronic instruments is the best choice. Suitable for libraries, offices, etc.
Q:What is the cause of the lights after the led fluorescent lights are turned off
This is the first problem of phosphor There are residual afterglow The same way as a luminous powder By light after light This in normal LED, it is not possible
Q:Are led fluorescent tubes not available for lighting?
But to see if there is a built-in power source, the external power source is not directly 220V,
Q:Buy LED fluorescent tubes to see which parameters
Power efficiency, power factor Output power (the voltage * output current of the output LED)/the input power. This parameter is especially important if the low efficiency means that a large portion of the input power is converted into heat. If it is installed inside the tubes will generate a very high temperature, and the led chip will generate heat, and would have a higher temperature, the superposition of all electronic parts within our power supply will increase with increasing temperature and shorten the service life. So the efficiency of power supply are decided life the most fundamental factor, efficiency is not too low, otherwise consume too much heat on the power supply. Power factor on the value, the power factor is the ratio of active power and apparent power, namely the cosine Φ = P/s. low power factor, can produce a large amount of reactive power, power efficiency and will also cause disturbance to the grid, it will be high to the requirement of engineering and the factory! General requirement efficiency is above 80, power factor is above 0.8. Brightness, longevity The current led lighting tube is 90-100lm/watt, and the life span is more than 20,000 hours, and the chips and power supply should be paid attention to. We adopt a 3-ampere, long power supply to ensure the quality of the lamp.
Q:Sales LED T5 T8 daylight lamp tube ask how to seek customer on the net
I also do this, and now the market for leds is not very big, only companies that are looking for engineering, energy efficiency projects. Don't search for an agent.
Q:An electric power saving device installed on an old-fashioned daylight lamp tube
Make a voice-controlled circuit to control the power switch.I hope my answer will help you.
Q:Can the LED tube be installed as a general lamp holder? It won't burn easily
Not necessarily, if you buy the lamp belongs to universal, some tubes into line is at one end of the tubes, so again after confirm the specification on the connection mode, when compared with the ordinary lamp holder, if can be general, will not burn.
Q:How does the T8LED light tube replace the fluorescent lamp tube
I just changed it. I bought a LEDT8 type of fluorescent tube 1 meter 2. 16 watts is basically equivalent to the ordinary energy-saving fluorescent tube 60 watts. It's very bright and bright, and you don't need a flash. But there are brands that don't have to take down the ballast, and you have to consult the person who sells your LED tube. The ballast and the regenerator are broken down, and the different brands are different.
We are a leading manufacturer of a broad range of LED strip light and LED Tube light. From 2011, we have integrating sphere spectrometer, high speed automatic placement machine, reflow soldering machine, automatic dispensing machines and other specialized equipment and professional R & D department. LED strip light can produce up to 300000 meters per month.

1. Manufacturer Overview

Location Shenzhen,China
Year Established 2011
Annual Output Value
Main Markets

Mid East;Western Europe
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Shenzhen
Export Percentage
No.of Employees in Trade Department 20 People
Language Spoken: Chinese
b)Factory Information  
Factory Size: Above 4,000 square meters
No. of Production Lines About 5
Contract Manufacturing OEM Service Offered;Design Service Offered
Product Price Range Cheap