T Type Ductile Iron Pipe DN80 socket spigot pipe

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
200
Supply Capability:
80000 /month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Specification:

1) The standard of pipe: ISO2531:1998, EN545:2006K9 K8

2) Effective length: 6m/5.7m

3) Inner cement line: Portland cement lineas per ISO4179

4) Zinc coating: at least 130g/m2 as per ISO8179

5) Bitumen painting: at least 70μm as per ISO8179

6)With 102% quantity of NBR, SBR, or EPDM ring asper ISO4633

7) DN80-DN1200

8) Highstrength, lighter than grey iron, good corrosion resistance, no furring, smallflow resistance, easy fixing, long life tome about 100 yeas

9)Checked by automatic inspection equipment

10) Composition:

Chemical composition

Chemical composition

Ductile Cast Iron  Pipe (%)

Grey iron pipe (%)

Steel pipe (%)

C

3.5-4.0

3.2-3.8

0.1-0.2

Si

1.9-2.6

1.4-2.2

0.15-0.4

Mn

0.15-0.45

0.4-0.6

0.3-0.6

P

0.06

0.3

0.02-0.03

S

0.02

0.1

0.02-0.03

Mg

0.03-0.06

 

 

11) Feature:

Mechanical  properties

 

Ductile Cast Iron  Pipe

Grey Iron Pipe

Steel Pipe

Tensile  Strength(Mpa)

420

150-260

400

Yield Strength(Mpa)

300

No Confirmation

No Confirmation

Bending  Strength(Mpa)

590

200-360

400

Elongation (%)

10

Neglected

18

Brinell  Hardness(HBS)

≤230

230

About 140

12) T type mechanical joint

13) Packing: in bulk or container

PACKING: 1) Pipesare bundled together with the steel belt.

2) Wooden pieces are put between the pipes.


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What does "K8" mean in ductile iron pipe grades?
In wall thickness, K is the standard for wall thickness. The smaller the figure, the thinner the wall thickness of the same specification.For example, the K7 wall thickness of K8 is less than K8, and the wall thickness of DN500 is less than K9
Q:What are the specifications of cast iron pipes?
The nominal diameter of the continuous grey cast iron pipe is 75~1200 mm. It adopts the form of socket type or flange disk interface. It can be divided into two kinds of flexible interface and rigid interface according to function. The length of the straight pipe is 4 meters, 5 meters and 6 meters. According to the wall thickness, LA, A and B are divided into three grades. The nominal diameter of the centrifugal cast iron pipe of the sand mould is 200~1000 mm, the effective length is 5 meters and 6 meters. According to the wall thickness, it is divided into two grades: P and G. High strength, good toughness, thin tube wall, little metal consumption, and can bear higher pressure,
Q:How long does the cast iron pipe of indoor direct buried sewage need to be examined?
UPVC, also called hard PVC, is an amorphous thermoplastic resin made by polymerization of vinyl chloride monomer, with certain additives (such as stabilizers, lubricants, fillers, etc.). In addition to additives, the method of blending with other resins is also applied to make it have obvious practical value. These resins are CPVC, PE, ABS, EVA, MBS and so on. UPVC has high melt viscosity and poor flowability. Even if the pressure and melt temperature are increased, the fluidity is not changed. In addition, the molding temperature of the resin is very close to the thermal decomposition temperature, and the molding temperature range is very narrow. It is a difficult material to be formed.
Q:Water supply pipe is ductile iron, then it's fittings and valves and other parts must be ductile iron?
Valve parts and materials do not require the same pipe material, as long as it can meet the use requirements and cost-effective.
Q:Why does the construction wastewater system use ductile iron pipes instead of galvanized steel tubes?
The sewerage system uses ductile iron pipes. The premise should be pressure pipe drainage. It must be a special occasion, otherwise the cost will be high. In general, precast concrete pipes are recommended.
Q:Why is the sound speed of nodular cast iron lowered after heat treatment?
After the heat treatment, the microstructure of the material changes, the graphite changes, eliminating the internal stress of molecules, thus slowing down the speed.
Q:Method for cutting cast iron pipe
Depends on the material and the use of requirements. Ordinary gray iron, if the incision is not strict, such as water pipes. They are all sheared with hydraulic cutting machine, but the incision will not be very smooth. If it is ductile iron, and the incision requirements are high, it can only be used plasma cutting machine. General fittings, if not specifically required, shall not be cut by machining methods.
Q:The difference between flexible joint cast iron pipe and flexible anti-seismic cast iron pipe
The appendix is selected so that readers can understand the design, construction and other contents of the ductile iron pipe. This book can be used for the manufacture and application of ductile iron pipe in the field of scientific research personnel, designers, production personnel, construction personnel, management personnel to read.
Q:Fire water supply network adopts ductile iron pipe, the test pressure should be no more than MPa
Strictly speaking: the outer pipe network and the internal pipe network are the same. Minimum fire 1.0MPa, minimum sprinkler 1.4MPa. Because not only in accordance with the water pump, but also take into account the pressure on the fire engine.
Q:Is ductile iron pipe breakable?
1 、 the drainage pipe is easy to fold. Folding is formed on the surface of various drainage pipe line, the longitudinal defects often throughout the entire product;2, poor drainage pipe surface prone to scarring;3, inferior drainage pipe, no metallic luster, is pale red or similar to the color of pig iron;4, inferior drainage pipe easily scratch, because the inferior material manufacturers equipment is simple, easy to produce burr, scratches the drainage pipe surface. Deep scrape reduces the strength of the ball drain;

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range