Super Agriculture Tyres

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

1. Good traction and protection;
2. Stable, comfortable ride;
3. Specifically resistance with long-lasting tread life;
4. Suitable for many conditions such as stone pit industry zone and underground mine.
5. Excellent cut resistance, effective heat dissipation & strong deformation resistance, can suitable for bad road condition



ROCKBUSTER BRAND, QUALIFY YOUR WORK!

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How many layers of steel tires are there in a big truck?
The truck tire is more commonly used bias tire and radial tire, the nylon curtain cloth embryo, the latter is a steel wire cord fabric embryo; at present, in addition to engineering or special circumstances, basically in the use of radial tire.
Q:Automobile tire exchange principle
First of all, please follow the instructions of the manufacturer's user manual regarding the tire alignment. If the vehicle manual does not specify, you may follow the advice given below:For vehicles equipped with new tiresIf the four tires are the same as the old, and the pattern has no direction, cross transposition can be used: right front, left, back, left, front, right and back.If the four tires are the same as the old, and the patterns have a direction, use the front and back changes: right, front, right, back, left, front, left, back.If the tires are different from the old, the new tire, the rear wheel, the old tire front wheel, left and right swap.Usually the pressure on the front and rear tires is different. You should adjust the air pressure at the location of the tire after you adjust the position of the tire.
Q:How often do they need to be replaced or when they need to be replaced?
Focus on the side walls of the car tires: as the tire rubber aging, the tire side wall will appear deep lines. However, as long as the sidewall of the tire is not impacted and the cord is not broken, it can continue to be used. The triangle mark on the side wall of the tire can help the owner find a protuberance in the groove of the crown, and can determine the actual wear limit of the tire. The value should be greater than 1.6 millimeters.
Q:How tight is the screw for the car tires?
A bolt or nut to play tight, in the automobile factory are clearly defined, control device factory with professional torque (torque torque, air gun, display setting or digital type torque wrench to ensure torque etc.). Different specifications and grades of bolts and nuts have specified torque range values. Here, give you a general reference range (the unit is N.m, referring to level 8.8): M8:20-30; M10:27-43M; M12:40-60; M14:60-80. Use air gun made after the torque value due to wind gun type and compressed air pressure of different sizes will be very different.
Q:What are the common problems that automobile tires need to pay attention to?
Tire pressure not only directly affects the tire life, but also closely related to traffic safety, but there is a lot to say about how much the tire pressure is. In fact, each car has a clear air pressure regulation, this standard value to the tire in the cold situation of the measured air pressure shall prevail. However, because many owners of the aerated tyre is hot, so check the pressure will be higher than the actual value, if inflation at this time according to the standard pressure, may be in low pressure state of the tire after cooling, so a lot of shop owners will be filling filling value slightly higher than the standard. Not too much depends on experience, so the numerical lacks accuracy. Therefore, when the tire is filled, try to keep the tire in cold condition, and the standard pressure should be detected under the condition of tire cooling.
Q:Are car tires vacuum tires?
Types and specifications: international standard tire tire code, expressed in millimeters and flat section height ratio percentage, followed by type code: tire, rim diameter (inches), load index (allowable load allowable speed, the quality of code) code. For example: 175/70R 14 77H, 175 represents the tire width is 175MM, and 70 represents the tire cross-section flat ratio is 70%, that is, the cross section height is 70% of the width, the rim diameter is 14 inches, the load index is 77, the allowable speed is H.
Q:Calculation of freight car tire consumption
In addition different brands vary greatly, the domestic three packs of semi-trailer axle wheel drive in picking only 6-8 million kilometers, Bridgestone can reach more than 250 thousand kilometers (drive shaft special M729), Michelin is said to have a can reach more than 400 thousand kilometers, not a lot of data support there is no way to do this calculation.
Q:Four tires on the same truck have different loads, can they be used?
The use of mismatched tyres has major effects:1, affect the transmission, traction and braking torque, the impact of wheel and road adhesion;2, affect the vibration and impact of the car in running, automobile parts are subjected to severe vibration and early damage,3, affect the driving safety, handling stability, comfort and energy saving economy.4, the tire does not match, affect the steering, easily lead to traffic accidents.
Q:What is the shelf life of ordinary freight cars?
Storage time is generally 3 years, depending on the storage conditions.If you use it, usually 5 to 80 thousand kilometers, specifically to see whether the tread pattern polished.
Q:Is the size of the car as big as possible?
Yes, tire design is very strict in science. It has to be balanced with load, speed, rigidity and elasticity. The principle of changing the wheel hub is to change the tire accordingly, so that the outer diameter of the tire stays the same or varies less than 5 millimeters.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range