straight seam submerged arcwelded pipe hydrotester
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
The introduction of spiral welded pipe/straight seam submerged arcwelded pipe hydrotester
Spiral welded pipe/straightseam submerged arc welded pipe hydrotester mainly is used to have the pressuretesting to spiral welded pipe or straight seam submerged-arc welded pipe. Ituses polyamine to have the end sealing and inner supporting large gas sealingmethods. It is assisted by oil water balance system. Besides, the computer canrecord, store, print and testing the results. Its advantages include pressuremaintaining stability, high safety and so on
The machine adopts the structure of the symmetrical plate tension rod, the center of force is in the symmetry center of the pull rod when testing pressure; the pull beam width on both sides is greater than the maximum diameter of the pressuretesting steel pipe, to ensure both sides security of the hydraulic press when testing pressure, the structuredesign is simple, the strength and stiffness superior, performance stable, easy to maintain and use;
Advantages
1 Pressurizing ways use high pressure intensifier.
2 The control system uses the system of “industrial computer (touch screen) +PLC", has automatic / manual / maintenance three work ways.
3. PLC selects Siemens S7-300/400 series, operation stable; control simple and flexible, has good scalability
4 The high-pressure water pump adopts frequency conversion control, boost rapid and stable, holding pressure fluctuation is small.
5 The host PC (touch screen) software real-time displays by pictures, curves, texts, and data, simple and intuitive.
6 Pressure-testing parameter setting is convenient and flexible and has storage, later called directly.
7 Has a perfect diagnostic function, the computer will provide real-time fault information, easy to maintain.
- Q:What is the surface rolling forming machine process?
- The rolling process using metal at room temperature, cold plastic characteristic, through the rolling tool is the rolling tool to put some pressure on the metal surface, so that the workpiece surface by plastic deformation, the height to the lower tissue slip, the surface roughness decreased.
- Q:Improvement in rolling forming process
- The rolling will produce a hardening layer on the surface of the workpiece. This layer has obvious delamination phenomenon with the internal material, which is easy to cause the surface layer to fall off;
- Q:A roll forming machine, rolling out of the length is always not up to a fixed size, not too small, that is, more than that, what is the cause?
- Maybe there is something wrong with that roller. It rolls out of the wrong angle and the size will be out of order.
- Q:What kind of material and what heat treatment are used for pressing roller (molding, feeding, cutting force, heavy load, heavy load) of sheet steel rolling machine?
- Generally speaking, to consider the use of rollers in the requirements, including: 1., good wear resistance, 2. toughness, 3., high hardness, 4. hardened layer (easy to wear after repeated repair)
- Q:Process mould for rolling forming process
- Rolling forming is more complicated and requires higher than rolling thread. The die design is based on the different shapes of the workpiece, the design of the rolling plate into a cross section or a few sections, can use synchronous type; also can use grading type.
- Q:What is rolling forming processing?
- A special rolling tool is used to exert certain pressure on the surface of the workpiece so as to make the surface metal flow.
- Q:Material and equipment for roll forming process
- The most common type of roll forming is reciprocating flat wire twisting machine. Therefore, for the manufacturers of cold heading machines and screw rolling mills, the design of rolling dies is only a matter of design.
- Q:Introduction of roll forming process
- Roll forming began around 1960s in europe. Because of roll forming, the working model has the advantages of high production efficiency, saving material and increasing product strength.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
straight seam submerged arcwelded pipe hydrotester
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords