STEEL WOODEN ARMORED MAIN DOOR DESIGN WITH ROB HANDLE

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

MAIN DOOR DESIGN
1.sunproof,waterproof.
2.material:steel&wood.
3.wood veneered+steel shelve as core.
4.size is ok.

MAIN DOOR DESIGN

NAMESTEEL WOODEN ARMOUR DOOR
SIZE2050X960MM
DOOR LEAF
THICKNESS
70MM/80MM/90MM
MATERIALCOLD ROLLED STEEL+HDF BOARD
DOOR STRUCTURECOLD ROLLED STEEL PLATE
+U SHAPE STEEL FRAMEWORK
+STEEL FRAME
THICKNESS OF
DOOR LEAF
0.8MM
THICKNESS OF
DOOR FRAME
1.5MM
LOCK13 LOCK POINTS
FEATUREANTI-RUST,SUNPROOF
PEEPHOLENORMAL
DOORSILLSTAINLESS STEEL DOOR SILL
HINGE90 DEGREE OPEN VISIBLE HINGE
DIRECTIONOUTWARD/INWARD
HANDLE POSITIONLEFT/RIGHT
SECURITYWITH ANTI-THEFT STRUCTURE


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Strong door, solid core wood door, or metal door?
solid core wooden doors can be kicked in easily go with the metal - no lites (that means windows) just a peep hole - key only dead bolt and don't leave the key on the inside side of the lock - a newspaper under the jamb and a pick can retrieve that key double lock - that deadbolt and locking knob don't forget to feed the rottie - he is better protection yet
Q:Aluminum windows and doors are hinged or hinged
Hello i'm professional to break the aluminum windows and doors of the bridge, of course it is equipped with hinges well if you hold the page wind it will swing
Q:Our home to aluminum alloy doors and windows, so urgent need to know the specifications of aluminum doors and windows
Aluminum alloy window thickness difference, and now the specification requirements of the main force of the site thickness of not less than 1.4, the door is not less than 2.0, another thermal insulation bridge aluminum window insulation performance better than ordinary aluminum doors and windows
Q:Aluminum doors and windows how the glass
Aluminum alloy doors and windows are generally used in hollow steel, can be 5 + 6A +5,5 +9 A +5 5 +12 A +5 6 +9 A +6 6 +12 A +6, etc., can also be a single layer of tempered glass such as 6mm, 8mm, 10mm, etc., can also be tempered glass. The most is the first wave. See what you want to achieve the effect of the!
Q:How to open an aluminum alloy doors and windows factory
My answer does not take the unusual way: open the shop as long as the individual industry and commerce on the line, the other if the department to check you to deal with the tax subsidies, no need to engage in anything, your focus is to shop to make money. To set up your factory, set up the company, the money you find the natural come back to find you.
Q:In microwaves ovens, can such waves pass through wooden or metal doors?
microwaves cannot pass through metal at all. even tin foil. the door of the microwave, as you might notice, has a sheet of metal with a bunch if round holes in it. the holes are just small enough that the microwaves cannot pass through them. as for the wood it would depend on what size. i don't believe that the microwave would pass through a piece of wood thicker than 1/2 inch. microwaves only penetrate food about a half to one inch. they cook the food by exciting the water molecules in the food and causing internal friction. the friction then spreads throughout the food. the wood should be enough to stop the waves. if you want to perform a science experiment put a glass of water in a wooden box and microwave it. the wood might get slightly warm as there is some water in wood. but if the water does not heat up then you would have your answer.
Q:How to clean aluminum doors and windows? Make it a new look.
Aluminum alloy has a special cleaning agent. You can use this point of the rub, do not use the kind of acid things, was very clean, how long before it may be black.
Q:How do I remove the inner (metal) door pannel on a 2000 VW Beetle? I need to replace the two door handle ret
I assume you are replacing the famous German junk door regulator with the plastic clips? Remove the door handle cover and undo the 2 screws under it. you will have to undo the star bolts along the outer perimeter and 1 or 2 in the center or right side middle. There are 2 or 3 plastic snap in clips you will have to pull out ( try easily backing them out with a screw driver. You will have to fish out the electric door lock arm. Just pull it out by removing the rubber boot. Unclip all the electrical snap In's!. There are 2 rubber grommets in the metal door. Take them out.push the glass up if you have to to get to the clips that hold the glass in place. Then loosen the screws up on both glass clips. Then pull the glass straight up and out of the car. Make sure you remove the molding around the window so you can grab the glass easily!
Q:how do i measure and cut to install a door in my block concrete garage wall. i have a 36 metal door.
Assuming your door is pre-hung, measure the jamb width (not the molding attached to the face of the jamb). Add 3 1/4 inches for your 2x8 lumber, ( you did buy treated didn't you?). Add another 1/2 inch for room to plumb the jamb in the opening. (I'm afraid you have to go back to the store to buy shims...get some great-stuff for doors and windows while you're there.) Measure height of door jamb. Add 1/4 inch for leveling. Mark wall using level. Cut blocks with concrete saw you rented while you were out buying shims and great-stuff. Pray wall doesn't tumble down on your head, ( You did remember to consult a qualified engineer. It's much better if you pay them to take the blame when things go wrong.) Fill voids in wall with mortar or cement. Tapcon treated 2x8 to opening using a generous amount of liquid nails I forgot to tell you to buy. (Back to the store again...you actually had tapcons and a hammer drill?). Finally...the door. Get out your six foot level and your three foot level. Shim bottom of door on hinged side about 1/4 inch. Plumb hinged side up shimming as needed. level across top. Plumb down other side. Use shims behind every screw. (You did buy screws). Fill voids with great-stuff. Caulk. Paint. Lightly oil hinges. Enjoy :)
Q:installing laminate obstacle - metal door frame?
Metal Door Jamb

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range