Steel Gate Valve with Good Price Made in China
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 1000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1.Structure of Gate Valve Description:
A gate valve, also known as a sluice valve, is a valve that opens by lifting a round or rectangular gate/wedge out of the path of the fluid. The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restriction is desired. The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry. For extremely thick fluids, a specialty valve often known as a knife valve is used to cut through the liquid. On opening the gate valve, the flow path is enlarged in a highly nonlinear manner with respect to percent of opening. This means that flow rate does not change evenly with stem travel. Also, a partially open gate disk tends to vibrate from the fluid flow. Most of the flow change occurs near shutoff with a relatively high fluid velocity causing disk and seat wear and eventual leakage if used to regulate flow. Typical gate valves are designed to be fully opened or closed.When fully open, the typical gate valve has no obstruction in the flow path, resulting in very low friction loss.
2. Main Features of the Gate Valve:
• Valve body cavity using non-toxic epoxy resin,both inside and outside flashboard completely is coated with rubber
• Free of water pollution
• High manufacturing accuracy
• High strength
• Environmental protection and energy saving
• Good visual effect
3. Images
4.FAQ
1. What's are the characteristics of gate valve?
The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restriction is desired. The gate faces can form a wedge shape or they can be parallel.
2. What is the work principle of gate valve ?
The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry.
3. What is the structure?
Bonnets provide leakproof closure for the valve body. Gate valves may have a screw-in, union, or bolted bonnet. Screw-in bonnet is the simplest, offering a durable, pressure-tight seal. Union bonnet is suitable for applications requiring frequent inspection and cleaning. It also gives the body added strength. Bolted bonnet is used for larger valves and higher pressure applications.
- Q:such as gate valve, three way plug valve
- The lower part of the pressure gauge installed water pipe, there are water, avoid high temperature, medium pressure gauge contact directly cause damage, so regular cleaning, in order to avoid congestion, three way plug function is used for flushing, please see "how to operate them.".
- Q:What does the valve QF mean?
- Valve type, one of the contents, Q refers to the ball valve, F refers to the F-4 seals.
- Q:Which valves are used in the power station?
- Power gate valve, also known as power station valve, is mainly used in various pipelines of fire power plants, cutting off or connecting pipeline medium.Applicable medium: non corrosive media such as water and steam. Compared with other valve products, the valve is characterized by high temperature and high pressure and unique self sealing design. The higher the pressure, the more reliable the seal is. Because of its performance, technical characteristics and special working conditions, the products can not be replaced by other products.Compared with other valve products, the gate valve of the power station is characterized by high temperature and high pressure. If only the pressure is lower than that of the universal valve, the temperature is lower than that of the general valve. Because of its performance, technical characteristics and special working conditions, the products can not be replaced by other products.
- Q:What are the most common types of valves?
- Gate valve, globe valve, check valve, ball valve, butterfly valve, safety valve, drain valve, plug valve, throttle valve, plunger valve, diaphragm valve, relief valve, foot valve, drain valve etc.
- Q:How to find all kinds of mysterious valves of human body?
- Many cell signal channels have been found, and if you can find each signal, the channel will be almost the same. That's the mysterious valve you want, but it's hard.
- Q:Proportional valve why than other small pipeline valves
- 3.8 valveGraphical representation of numbers, names, symbols3.8.1 angle valve at room temperature3.8.2 cold angle valve for low temperature use3.8.3 stop valve at room temperature3.8.4 ball valve often 9 temperature3.8.5 valve at room temperature3.8.6 butterfly valve at room temperature3.8.7 check valve flow from blank triangle to non empty triangle3.8.8 pressure reducing valve, small triangle for high voltage end3.8.9 throttling valve is needle valve3.8.10 three-way valve for normal temperature use3.8.11 four way valve used at normal temperature3.8.12 safety valve spring type safety valve3.8.13 trap actual drawing, you do not have to draw arrows3.8.14 inflator, cold box, little gas huff and puff, safe useValve for normal temperature of regeneration valve of 3.8.15 reverse stop valve3.8.16 reverse loading cold angle valve
- Q:What kind of valves are best used for sand drain valves?
- Suzhou ATW Valve Co. Ltd production of sealing ball valve, Suzhou ATW Valve Co., according to the condition of solid particles, long-term research and in practice, and achieved good results in the condition of solid particles. You can try!
- Q:What does "1/2" mean on the valve?
- 1/2 on the valve indicates that the ends of the valve are 1/2 inches in diameter.Valve is a control component in the fluid delivery system. It has the functions of closing, adjusting, guiding, preventing reverse flow, stabilizing voltage, shunting or overflow and releasing pressure.Valves used in fluid control systems, from the simplest stop valve to a very complex automatic control system used in a variety of valves, a wide range of varieties and specifications. Valves can be used to control air, water, steam, a variety of corrosive media, mud, oil, liquid metal and radioactive media and other types of fluid flow. The valve according to the material is divided into cast iron valves, cast steel valves, stainless steel valves (201, 304, 316), chrome molybdenum steel, chromium molybdenum vanadium steel valves, valve, dual phase steel valves, plastic valves, non-standard customized valve material etc..
- Q:What is the difference between the valve before the pump and the valve after the pump?
- Pump front valve: current limit; pump rear valve: limit pressure.Pump operating procedures: the pump must be closed before and after the valve, open the pump, slowly open the pump front valve, pump pressure normal, slowly open the pump, valve until all open. If the pump is in front and rear valves are opened, the pump is very easy to burn the motor.
- Q:I would like to ask, how specific treatment, and compared with the industry?.Is there a constructive answer?
- I have to do the technical sales colleagues is high inside out now before the inside sales revenue is also good about one hundred thousand a year as sales of a great degree of luck the.I do not know what the specific circumstances, what age, in this line for several years, there is the opportunity to communicate with the landlord and make progress together.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Steel Gate Valve with Good Price Made in China
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 1000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords