square canned food can seamer
1.18 years experience
2. Delivery in time
3. All brands can supply
4. 100% origin
Main technical parameter:
food can seamer
Thickness of tinplate≤0.5mm
Diagonal line of can
Heighe of can
Power of motor
1)This GD Capper is designed by the engineer of our company, and we have the patent of it, the patent number is ZL002015552.
2)GD can seamer is applied to seal 1-4L square tin cans, it is used to seal can lid and can bottom at can body tightly, without leak.
3)if customers want to seal other size of cans, just need to chage the sealing mould.
- Q:How to prevent the welding spot welding workpiece
- 1, adjust the welding parameters: welding current and voltage of different materials and different thickness of the welding speed is not the same, you are suggestions according to the welding materials to do a sample test, find a suitable welding parameters. After the test piece is finished, do the welding evaluation, the appearance defect and the fusion depth. The size of the fusion can be cut into specimens, and the size of the weld is determined by pickling. The solder joints are fused into the weldment.2. Preparation before welding: the weldment is made of aluminum and the surface of aluminum is covered with oxide film. The film must be cleaned before welding and cleaned or pickled with wire brush. Because the melting point of the oxide film is above 1000 degrees, and the melting point of the aluminum material is below 1000 degrees, the existence of the oxide film prevents the fusion of the solder joint and the base metal. The estimate is the main reason. After the oxide film is cleaned, it should be welded within 3 hours. Otherwise, the film will be re oxidized with air.
- Q:Spot welding temperature is too high to deal with
- It's pedal like. But the water pipe is also connected. However, the solder joint temperature is still very high. I also adjust the temperature control of the controller, but still the same as usual, welding contact points are black, welding surface also appeared a lot of holes, how should I deal with it?
- Q:What copper is suitable for spot welding machine contact?
- Take the main transformer of the 5KW household regulator, remove the movable contacts and other accessories. Separate the two layers inside and outside the coil. The inner layer doesn't need to be used. 2.5 with the same number of cotton round a layer, as the primary. Take the 2*9 flat copper wire around the 42 ring,
- Q:What brand is battery spot welder good?
- Do you want welding caps or pack? Youni'en spot for good, good customer service
- Q:Is spot welder controlled by PLC?
- Now the general control is PLC. In addition to time, there are currents, pressures, etc., which are controlled.
- Q:What's the capacity of the 150 160KVA power frequency spot welding machine in the welding workshop?
- Manufacturers to help you count it, generally interlocked, it is impossible to work at the same time, manufacturers will be considered when installing an tddhj
- Q:Can ring transformers be used as spot welders?
- The theory is OK, but the ring transformer power is too small to be suitable, and it is recommended to use E transformer or C type transformer
- Q:What are the differences between medium frequency inverter spot welder and high frequency inverter spot welder?
- Welding inverter frequency is not high. Strictly speaking, it is medium frequency inverter. Usually the switching frequency of tens of KHz called MF, 100KHz or better known as high frequency. Generally speaking, most of the small power machine are designed more than 100K. If the welding welding machine of big power module do you usually like this. 2025Khz is also useful discrete MOS, will be designed to more than 100K.The difference in performance is not good, welding can be done well, because the inverter welding machine final output is DC. What is the switching frequency on the performance of little impact?Of course, seriously, the power of the proposed use of the so-called "intermediate frequency machine", how to say that is also designed to use modules, and spend money is worth
- Q:Is the smoke from the spot welding machine poisonous when it is welded?
- Some, leading to infertility, killing sperm.
- Q:What are the materials for the nut locating pin of the spot welder?
- KCF of ceramics
In area of technic, research and development, We have a batch of professional and technical personnel in product development and manufacture and production management, some of our products have applied patent, so we believe our high technology and high quality products can meet the updating requirements of customers. We always keep "good business by sincerity and honesty, client's profit in first position" as our management principle. And we have been appraised as a corporation that "pay importance on contract, and keep sincerity" by local government for many times.
1. Manufacturer Overview
|Annual Output Value
||Below US$1 Million
||South America 1.04
Southeast Asia 3.26
Mid East 8.81
Eastern Asia 0.54
South Asia 2.25
Domestic Market 76.18
||Consumer Trustworthy Company;Member of Chiese packaging technology association;Trust-worthy Company
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||41% - 50%
|No.of Employees in Trade Department
||5,000-10,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered
|Product Price Range