spider lift 23m

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Model:

FM230

Max.working height

23m

Max.platform height

21m

Loading capacity

200kgs

Lateral Outreach

9.30m

Platform rotation

180°

Jib rotation

120°

Turntable rotation

360° non- continuous

Size of platform

1.2*0.8*1.1m

Overall stowed length

6.50m

Overall stowed width

1.60m

Overall stowed height

2.10m

Power capacity

 

Standard power source

diesel engine    

220V AC power

Driving speed

0-1.7km/h

Max climbing ability

30°

Total weight

3700kgs


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What can be done when the hydraulic platform is down?
You can't see your schematic diagram, theoretically do not use hydraulic lock, should balance valve, the frequent switch of hydraulic lock causes jitter and unstable. Shunt valve, speed regulating valve or pressure compensating valve is a common solution to solve synchronization problem. Synchronous diverters are expensive
Q:Simple manual lifting mechanism, a nut a bolt can
The next face is worn, welding a circle, ok turn, rise, also can not be fixed, also can rise! The general problem is not too big, it's a two-point position, if it's fixed at three points, it's high in accuracy
Q:What is the phenomenon of the worker's transport of wood using a lift
Imobile elevator accessory device can be configured for any combination, such as lifting capsules can be used with the inward and outward transportation equipment, make fully automated conveying process, operators need not enter the elevator, so as to ensure the personal safety of operators, and can realize the goods transport between floor, to improve the production efficiency; Electrical control mode; Work platform form; Dynamic form, etc. Limit the function of the elevator to achieve the best use effect. Imobile elevator optional configuration of hydraulic power, convenience and the surrounding the lap joint of frame, roller rolling or motor, prevent pinches safe touch, organ type safety guards, moving or motor rotary worktable, hydraulic flip table, to prevent falling elevator safety support bar, stainless steel security guard network, power system of electric or hydraulic elevator walking, mesa of ball. A stationary lift is heavy in weight. It's not affected by the environment.
Q:Why is the large laser engraving machine plus half the platform?
About whether to lift: all are generally two kinds of the lifting methods at present, screw support lifting and hydraulic elevator, screw because of the limitation of itself bearing part can only support plate lifting platform, so generally make some lifting; Hydraulic lift, JQ1325 hydraulic lift can be fully raised, the hydraulic platform can carry 4-10 tons of stone. More questions can be asked about the r&d department of jinan jinqiang laser digital control equipment co., LTD.
Q:How does the elevator repair
All parts should be filled with lubricating oil to extend the life of the bearing. The oil and oil level of hydraulic oil. The platform rises all the way up, and in this position, the hydraulic pressure should be 40 to 50 mm above the bottom of the box. Hydraulic oil is a variation of dark, sticky or grit, such as a discovery should be replaced in time (32 # hydraulic oil) Annual maintenance A. check all the hydraulic pipes and connectors. The pipe shall not be broken, the joints shall not be loose, and all the joints must be tightened. Remove and disassemble the descending valve, blow the plunger through compressed air, then load and resettle. C. the elevator hydraulic oil is put in the rejected, tighten the joint remove oil filter, after cleaning, use compressed air is clean, and then back into the tank, and the connecting line. (put on new oil and don't keep using the old oil. Otherwise, the moving parts in the system will accelerate the wear and tear.)
Q:There are several reasons for the hydraulic cylinder oil leak on the elevator
Oil cylinder in and out tubing joint cracking; (I've seen a lot of this in practice.) 2) the sealing damage of the piston rod with the piston rod is caused by the pull of the piston cylinder. 3) cooperate with cylinder liner piston rod out end seal is damaged, this is caused by long-term use of seal aging more, also has a lot of end cover on is too hard to seal extrusion is damaged, there is a lot of domestic manufacturer of hydraulic cylinder design is not reasonable cause (mostly in order to save costs)
Q:The purpose of the rail elevator
Guide lifter is a kind of hydraulic elevating shear machinery and equipment. Used for secondary and tertiary industrial workshop, restaurant, wine shop floor between the transport of goods. The minimum height from 150-150 mm, optimal it is suitable for the workplace can't excavation pit. And do not need the upper lifting point, in the form of diversification (single column and double column, the four pillars). Equipment running smoothly, guide of elevator guide rail is commonly channel steel, H steel, square tube welding, operation is simple, reliable and convenient transport of goods economy.
Q:The automatic mahjong machine has a lift station always one. What is the other three normal
There are two main reasons for this: In the ascent of the aluminum plate, the interference with the limit mechanism
Q:There is no elevator on the 7th floor of the home to install a lift or lift
What do you want to do? Can you agree to install these things? These later additions can only be set outside the building, affecting the fire channel.
Q:What happens when the platform comes up and the power goes out.
Many platforms have an emergency drop.I hope my answer will help you.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range