Rate Power: 600W
Peak Power: 1500W
AC Output Voltage: 110VAC,220VAC,240VAC
DC Intput Voltage: 12VDC,24VDC
Wave Form: Pure Sine Wave
Overload Protection: 700W
Working temperature: -20 oC to 50 oC
Gross Weight(Packing): 4.1Kg
* Solar Charger Specification
· Solar Intput Voltage: 12VDC,24VDC
· Solar Intput Current: 8A~13A
* Inverter Function
· Solar Generator Connector on inverter body
· LED Display
· Over-Charge Protection
- Q:How to use digital multimeter to detect the quality of 36 volt low voltage lighting transformer?
- If there is no painting can be used with a diode symbol file (measuring probe connected to the capacitor to hear a sound if the table does not ring at the table and then the general display is 1, then the pen on the emergence of the phenomenon that the capacitance is still good. If one table has been ringing that received the capacitor capacitor breakdown is broken)
- Q:Why should lighting transformers be used in factories and mines?
- There are two cases. One is the general factories and mines, and the low voltage is three-phase four wire system, and the neutral point is directly grounded. Between the phase line and the zero line is 220V, which can be connected with the illumination load.
- Q:How many A leakage protection switches are used in 5000VA lighting transformers?
- According to the working principle of the protector, it can be divided into three kinds: voltage type, current type and pulse type. The voltage protection device is connected to the transformer neutral point and the ground, when the electric shock when the neutral point voltage offset to the real estate, in order to make the action to protect the power off, but because it is the protection of the transformer low voltage network, cannot be classified protection, so the power range is large, frequent moves, so has been eliminated. The pulse current protector is a sudden change in the phase and amplitude of the three-phase unbalanced leakage current when an electric shock occurs, which is used as an action signal, but also a dead time. The current type current leakage protector is widely used, so the protector of current type is mainly introduced below.
- Q:Can the 500 volt lighting transformer be changed into an electric welder?
- The no-load voltage is higher (about 70~90 V), the arc can be smoothly started, and the voltage will be reduced to about 30 V when welding.
- Q:Which is more energy saving by using 24V500W transformer lighting and 220V500W lighting?
- If the transformer is not calculated, the loss is the same. If the calculation is the latter, save electricity.
- Q:1000 square meters low voltage.36 volts lighting power supply with multiple transformers and wires
- You must know the quantity and power of the lamp to determine the transformer
- Q:Is the substation separate from the power and illumination transformer?
- The power and illumination of the substation are all used on a transformer, which is separated by power and lighting by the station screen of this transformer.
- Q:The transformer zero line has broken, has the result to the household illumination circuit?
- The lighting circuit mostly 3 phase unbalanced load, there will be zero drift, zero if the transformer line is broken, part of the lighting circuit to form a series of equipment in the case of two-phase circuit, circuit voltage is decreased and the lighting brightness is not enough, circuit voltage increases, the lamp burned;
- Q:Line lights, lighting transformers in use!! Can live line work?!! Be afraid of electric shock 40
- What you think? Your light is 220V, right. Over 36V, it's better not to live with electricity unless there is good protection
- Q:Please tell me how to calculate the transformer in the lighting circuit of elevator shaft in building electrical design
- Because of the brightness of the 36V safety voltage lamp brightness in the overhaul work is not enough, so now the well lighting design should not be 36V, and replaced by 220V, and only need to add a leakage protector on it.
We strongly believe that you will be satisfied with our whole services, no matter in attitude, respond time, information offer before sales, technical support, prompt delivery, after-sales services, and customer quality claim issue.
1. Manufacturer Overview
|Annual Output Value
||North America; South America; Eastern Europe; Southeast Asia; Africa; Oceania; Mid East; Eastern Asia; Western Europe; Central America; Northern Europe; Southern Europe
||Invention Patent Certificate; Utility Model Patent Certificate
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||71% - 80%
|No.of Employees in Trade Department
||1,000-3,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered
|Product Price Range