Solar Panels made in Thailand with hot selling

Ref Price:
Loading Port:
Guangzhou
Payment Terms:
TT OR LC
Min Order Qty:
26 pc
Supply Capability:
100000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

Characteristics of Polycrystalline Solar Panel

I Solar Cell : High efficiency crystalline solar cell. Even if under the weak light, the solar module can produce maximum power output.

II Tempered glass (toughened glass): Anti-reflecting coating and high transmission rate glass increase the power output and mechanical strength of solar module.

III EVA and TPT: Using high quality EVA and TPT to prevent destroying and water.

IV  AI frame: Without screw, corner connection. 6 holes on the frame can be installed easily.

V Junction box: Multi function junction box with water proof.

VI Long lifetime: ≥25 years; Less power decrease.

VII Good performance of preventing from atrocious weather such as wind and hails.

VIII Resisting moisture and etching effectively, not effected by geology. .

 

Standard Test Conditions of Polycrystalline Solar Panel

The opto-electrical specifications shown below are stabilized values being measured at Standard Test Conditions of multicrystalline silicon Solar Panel, Irradiance: 1000W/m2, Spectrum: AM1.5 at 25°C, The info below is subject to manufacturing tolerances. Where appropriate minutes of measurement are available and are used for the dimensioning of the installation.

Currently,We have 250w-300w solar panel stocks in Both West and East Coasts made in Vietnam,India,Korea,Malaysia and Japan.Meanwhile,we also arrange production line in Wisconsin,USA.If you're interested,please contact us soon.

Thanks for your time.

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Solar panels single crystal and double crystal in the rain which is easy to use
From the cost of production, than the monocrystalline silicon solar cells to be cheaper, easy to manufacture materials, saving power consumption, the total cost of production is low, so get a lot of development. In addition, the polysilicon solar cell life than monocrystalline silicon solar cells shorter. From the performance and price ratio, monocrystalline silicon solar cells also slightly better.
Q:What is the working principle of solar panels?
No matter what kind of material to make the battery, the general requirements for solar cell materials are
Q:Can cold light make solar panels power
The drawback of solar thermal power generation is that the efficiency is low and the cost is high, At least 5 to 10 times more expensive than ordinary thermal power plants.
Q:What is the difference between solar panels and light panels?
The production of silicon requires that the stone be heated to become liquid, and the heating becomes gaseous crystals. During the need to burn a lot of fossil fuels and emissions of toxic gases silicon tetrachloride, this material has a corrosive effect on the skin. After pickling, pulling crystal, cut the side, finished a series of processes, more industrial chain. The cost of the finished product is too high. The energy consumption of making a solar cell requires solar cells to be equal in power generation for several years. The cost recovery period is very long.
Q:Can solar panels be connected directly to motor?
Power supply must be a number of individual battery strings, connected in parallel and tightly packaged into components.
Q:Polycrystalline solar panels are good or single crystal solar energy is good
Polycrystalline silicon solar cell production process and monocrystalline silicon solar cell almost, but the polysilicon solar cell photoelectric conversion efficiency will have to reduce a lot of its photoelectric conversion efficiency of about 12% (
Q:The voltage and power problems of solar panels
From morning to night (with sunshine) solar panel voltage is generally relatively stable, that is basically about 30V; but the output power is always changing, sooner or later, noon; if it is good quality solar energy,
Q:What is the principle and structure of solar panels?
solar controller: the role of solar controller is to control the working state of the entire system, and the battery played a charge protection, over discharge protection role. In the larger temperature difference, the qualified controller should also have the function of temperature compensation. Other additional functions such as light control switch, time control switch should be the option of the controller;
Q:What is the principle of solar panels work?
The sun is irradiated on the semiconductor p-n junction to form a new hole-electron pair. Under the action of the p-n junction electric field, the holes flow from the n region to the p region. The electrons flow from the p region to the n region, and the current is formed after the circuit is turned on. This is the photoelectric effect of the working principle of solar cells.
Q:How many solar panels have ah?
However, crystalline silicon (monocrystalline silicon and polysilicon) in the weak light is basically no current generation, amorphous silicon weak light type (in low light energy is rarely). So a comprehensive view, it is appropriate to use monocrystalline silicon or polycrystalline silicon solar cell materials. Second, the choice of solar cells 1, we buy solar cells, the focus is on the power of solar cells, in general, the solar panel power is proportional to the area of ​​solar chips.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range