SMC sheet, SMC roving with Glass Fiber Roving 2400 tex with High Quality/Best Price
- Ref Price:
-
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 m²
- Supply Capability:
- 5000000 m²/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Introduction
SMC is the short form of sheet mounding compound. This is a raw material for mold pressing. The core is chopped strand and unsaturated polyester resins paste that are covered by LDPE & HDPE sheet. It is 3mm-6mm thick , 600mm-1200mm wide and packing in rolls or boxes. When using , be sure to cut , weigh , uncover film, and join in the heat up mould, after adding high pressure and preserve a time, then you can take off membrane to get the product.
Feature
l Higher mechanical strength
l Excellent leak-proof electrical
l Low water absorption, good dimensional stability, war page small
l Reliable arc resistance and voltage withstand, high dielectric strength
Specification
Product name | Fiberglass Reinforced Polyester Corrugated Sheet |
Material | High-performance protective film, unsaturated polyester resin, fiberglass |
Layer | 1 layer |
Width | 900mm,930mm,1100mm |
Thickness | 0.8mm,1.0mm,1.2mm,1.5mm,2.0mm,3.0mm |
Length | 5800mm,11800mm or customized according to requirement of customers |
Color: | Clear, Red, Yellow, Green and opal |
Guarantee: | 10 years |
Certification: | ISO9001 SGS ROSH |
Delivery time | 5-7days(general) depend on the style and quantity |
detail features | 1.The light transmission It is between 60-85%. Light through FRP lighting sheet scatters and is mild. It will not form a light band so as to make the indoor brighter. |
Advantage
l Solution of wood steel plastic meter box easy to aging, easy corrosion, poor insulation, poor cold resistance, poor flame retardant, the short life of the shortcomings
l Absolute seal waterproof performance, corrosion resistance
l Beautiful appearance, long service life
Application
1. Application in automobile industry
(1) Suspension parts, front and rear bumpers, instrument panels and the like
(2) Car body and body parts, body shell, hard shell roof, floors, car doors, cooling air grille panels, fore plate, spoiler, luggage hatch cover, sun shade, SMC fender, engine bonnet, headlight reflector
2. Application in rail vehicle
SMC railway vehicles, window frames, bathroom components, seat, coffee table tops, SMC compartment wall and SMC roof
FAQ
1. How about the documents after shipment?
After shipment, we ll send all original documents to you by DHL, including Packing List.Commercial Invoice, B/L, and other certificates as required by clients.
2. How long is the delivery time?
Usually it takes 10-25days after receipt of the deposits or L/C, and it also depends on the quantity of your order.
3. How's the payment?
Telegraphic Transfer(T/T) or Letter of Credit(L/C)
FACTORY
PACAKGE
- Q:What composite material is used for composite manhole covers?
- The composite manhole cover is made of unsaturated resin and calcium powder as base material, glass fiber as reinforcing material, and thread steel as skeleton. Patented technology, high temperature and pressure molding.
- Q:What is the difference between plastic die casting and compression molding? Please be specific
- Equipment: simple, but also the main features of plastic equipment. The two halves of the platen are joined together to heat and pressurize the material into a predetermined shape. Most pressing processes are hydraulically operated; pneumatic operations are also used. On the two plate moves in the 4 corner posts up and down under pressure. According to the size of press and mould equipment, the pressure is usually 20 - 1000 tons. The size of the platen is usually 8 inches, 2 to 5 feet, 2.There are different degrees of automation in the mold release after charging and curing. The most modern hydraulic press is often used. Previous simple systems include temperature control, pressure control, stop pressure control, and time control. Modern equipment is controlled by more advanced microprocessors. For thinner products, a heating cylinder or belt heater can be used in the plate. For deeper parts, use a cylindrical electric heater, steam heating or hot oil heating system. There are several kinds of pressure heating system used in plastic with uniform temperature steam heating mode, but the heating temperature limit below 350 DEG F; barrel heating or other heating (heating coil, heating etc.) is relatively clean, easy to maintain, with more universal; oil heating, because the heating medium circulation is stable, so the uniform heating. Now there are many new heating methods, hot water heating, similar to hot oil heating, heating medium, one water, one gas combustion, continuous cycle, can provide higher plastic temperature.
- Q:The difference between glass fiber reinforced plastic antenna and cannon antenna
- Cannon antenna is commonly used as glass fiber reinforced plastic antenna.
- Q:Seeking better SMC manufacturers in the industry, it is best to write more, thank you!
- I don't quite understand your question. SMC has only one manufacturer. I'm the agent of SMC. You don't know much about it
- Q:Does floor heating emit toxic gas?
- One check: check the product radioactive test report, see if the radioactive material is over standardTwo test: Please professionals with instruments for radioactive detection, to see whether and product radioactive test report in line with
- Q:Is the SMC material poisonous?
- This material is very good, non-toxic, give you a link, you refer to, remember to give a adoption Oh!
- Q:What material is the resin composite manhole cover made of?
- Glass fiber yarn, filler, resin, curing agent, accelerator, mold, etc.
- Q:Is the quality of the resin wall the same?
- From the installation form, it is divided into the gusset and the panel, the gusset plate is installed with the keel, and the panel is pasted on the wall with glue.
- Q:What are the raw materials for composite manhole covers?
- Because the SMC polymer resin composite covers are made of resin and SMC polymer sheet pressing, without reinforcement than usual covers light weight 2/3, but this kind of SMC polymer resin composite covers and not because of its weight and reduce its carrying capacity, SMC polymer resin composite well cover bearing is three times that of ordinary resin composite manhole cover bearing, up to 90 tons
- Q:What is the use of resin fiber powder extracted from the circuit board without breaking the law?
- The general concept of glass is hard and brittle objects, not suitable as structural material, but as the thread, the strength is greatly increased and is flexible, with resin to give it shape can finally become excellent timber structure. Glass fibers increase in strength as their diameter decreases. As reinforcing materials, glass fiber has the following characteristics, which make glass fiber use much wider than other kinds of fiber
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
SMC sheet, SMC roving with Glass Fiber Roving 2400 tex with High Quality/Best Price
- Ref Price:
-
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 m²
- Supply Capability:
- 5000000 m²/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords
