Slitting and Cut to Length Machine Line No.10
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 2000 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
General Information：
High speedslitting and cut to length can cut steel with thickness from 1mmto 16mm, if noneed slitting thickness up to 30mm.
Sandwichpanel, as a new building material，shows excellent performance oninsulation. We can design the line to make different kinds of panels inappearance, for wall panel and roofing panel with various joint designs.
It is takingthe place of brick to be a main material for building now.
Processing flow is as following:
Carry coil→loadcoil→de-coiling（pressingguide +opener）→entry、roughlevel→cutting→transition→guide→slitting (waste winding) →loopingstorage→pre-separating, damping→recoiling→packing→discharging→guide→leveling→fix size (end platefeeding)→cutting→discharging
Technical Data：
1. Coil Thickness：0.3-4mm
2. Coil Width：300-1800mm
3. Coil Max. Weight：30 T
4. Coil I D：φ508-φ800mm
5. Material: carbon steel platewith σb≤550Mpa、σs≤350Mpa
- Q:Why does a bar break occur in a bar splitting machine?
- Bending caused by uneven tension: the same tension is applied to the entire width of the steel plate when the volume is closed. Bending occurs if tension is concentrated on one side
- Q:There is a gap in the size of the strip machine, and the material is burr. Is the cutter axis beating or something else? How do you solve it?
- The overload of the uncoiling machine and the overcurrent alarm of the converter.Solution, turn off the main power supply of the electronic control system and restart it.
- Q:Slitting machine; batten; place
- When feeding should pay attention to the unloading arm pulley to kill, to prevent the unloading arm and the winding shaft from the material off injured foot.
- Q:What are the features of a metal slitting machine?
- The utility model is composed of an uncoiling machine (a discharging machine), a leveling machine, a material positioning device, a slitting equipment (a shearing device), a winding machine (a material collecting machine) and the like.
- Q:BOPP belt separator generally what price?
- One is KH210 type, including split main machine, pipe cutting machine, small rewinder, tube mill, 2 sets of moulds, type 202, 41000 yuan, type 210, 44000 yuan
- Q:What is a striping machine?
- What kind of slitting machine, flat knife or double-edged sword?. Laminating machine or slitting? This question also concerns the thickness of the original roll, for example, the original roll is 1 millimeters thick
- Q:Is the tape on the tape slitting machine a good one at the back or a good one in front?
- If you are concerned about the volume from the front. Mainly depends on your mother roll size, whether to change regularly, the quality of mother roll, how about, do not pay attention to its condition. Very few people ask this, I may not consider the full, you have the right to reference!
- Q:The belt machine used for gluing buckles lacks power
- Ignition, high pressure and ignition energy are normal, check ignition timing, cylinder pressure and engine mechanical failure
- Q:How do metal slitting machines cut out knives?
- The cutting skills of the slitting machine in the bar machine, and its Pai skills, mainly depends on the specific situation. If it is a good quality slitting machine, then it will be equipped with cutter software to carry out the correct arrangement.
- Q:How is the gap between the cutter and the cutter in the metal slitting machine measured without damaging the knife?
- A variety of equipment will be the entire corrugated cardboard production process organically combine, so that its continuous production. The traditional methods of combined production of more units and single machines not only have high production efficiency, low labor intensity, but also operate centralized control, which is simple, safe and low noise. The most important thing is that the corrugated paperboard produced is of high quality.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
Slitting and Cut to Length Machine Line No.10
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 2000 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords
