It is characteristic of efficient energy-saving, small noise, reliable performance.
- Q:How long will the oil pump lubricate the engine parts after the engine is started?
- The oil pump is driven by the engine. As long as the engine is running, the oil is pumped to the parts that must be lubricated at once. The crankshaft splash lubrication is of course another matter
- Q:Bending machine, cutting machine oil pump broken, how to judge?
- If it is winter, may be relatively thick oil, if it is not possible oil problems, there may be the problem of voltage, if it is the problem of the pump, it will not be less pressure is so simple. Where can you find someone to see?.
- Q:Accord 2 is timing, how about the oil pump?
- The pump also has a black spot on the point, even after a good bit and two black spots, a black spot on the point on the crankshaft, the two point of the oil pump is point, how many chains count on both sides, there is several section of the chain tensioner the!
- Q:Questions about the old Chery, the oil pump and the engine
- Bearing for a set or a low pressure, caused by many reasons, when you hold tile caused by the lack of oil, bearing should replace all, then replace the oil pump, oil lubrication is not good water temperature will be high, the fuel with the lights to replace the sensor
- Q:The car oil pump is broken. What are the problems?
- There's no trouble. You're not going straight
- Q:Is the engine speed the same as the pump speed?
- No, the ratio is 2:1. The oil pump turns two times and the engine turns around
- Q:What is the cause of engine oil alarm?
- Oil lamp alarm reason::1, the amount of oil is insufficient, so that the pump oil pump volume reduced, or because of air into the pump does not oil, resulting in lower oil pressure;2, the engine temperature is too high, easy to make oil thinning, from a large gap in the gap between the resulting oil pressure drop;3, when the oil pump parts damage or wear, assembly and other problems arise when the gap is too large, will cause the oil pump out of oil or the failure of the oil shortage;4, the crankshaft and large, small tile gap between the improper, too tight will make the oil pressure rise, too loose will make the oil pressure lower;5, the oil filter and oil suction disc plug will also reduce the oil pressure;6, the oil return valve damage or failure: if the main oil return valve spring fatigue softening or improper adjustment, the valve seat and the ball with the surface wear or dirt stuck and closed, the oil return amount will increase obviously, oil pressure of the main oil channel also decreased;7, improper selection of oil: if you use the wrong or improper selection of grades, the engine will run when the oil viscosity is too low and increase the leakage, thereby reducing the oil pressure;8, the oil pipe in the oil leakage, plug phenomenon.Only normal oil pressure can ensure that the oil is sent to all the friction parts of the engine, too high or too low will affect the normal operation of the engine, and even cause damage to engine parts. So, when the alarm lamp should be immediately shut down to find out the reasons, troubleshooting before it can continue to work.
- Q:What's the use of the oil pump for motorcycles?
- Two stroke engine oil pump is regulated through cable, throttle in the middle line will be divided into two, one to one to the carburetor, the oil pump, the throttle fully closed, then adjust the speed nut oil pump on the cable, the cable to completely relax, this is the minimum amount of oil, but be careful not to too loose, when the twist of the throttle, engine oil pump should follow the action, there is a situation of oil pump through internal wear caused by excessive amount of oil used for many years, this situation can not be adjusted, only the replacement of oil pump.
- Q:What's the reason that I changed the new oil pump instead of the engine oil?
- Did you try the oil pump before loading?
- Q:How to check the motor oil pump oil supply is normal?
- In the premise of the normal amount of oil, usually need to check whether the oil pressure is normal (usually around 0.3MPa), if the oil pressure is low, usually the oil circuit, overflow valve failure or oil pump failure. After cleaning and adjusting the oil relief valve, the pressure is still low. The fault must be the oil pump failure.The effect of the oil pump is to press the engine oil to a certain pressure and force it to the surface of each part of the engine. If the oil pump is damaged or leaking, it is necessary to disassemble the oil pan, take out the oil pump and replace it, and clean or replace the oil pump inlet strainer at the same time.
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||51% - 60%
|No.of Employees in Trade Department
||Above 100,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range
||High and/or Average