Quick Details of Six High-pressure Hose Wire Entanglement
Place of Origin:
Specifications of Six High-pressure Hose Wire Entanglement
Six high-pressure hose wire entanglement
High pressure steel wire braided rubber hose
your satisfaction is our pursuit...
CONSTRUCTION This hose consists of an inner tube of oil syn-thetic rubber,six spiral wire reinforcements,and an oil and weather resistant synthetic rubber cover.
APPLICATIONSHose range suitable to carry hydraulic fluids such as gly-col,mineral oils,fuels,lubricants,emulsion,hydrocar-bons etc.
The Technical Parameters of Six High-pressure Hose Wire Entanglement
Inside Diameter mm
Reinforcement Diameter (mm)
Outside Diameter (mm)
Work Pressure (MPa)
Proof Pressure (MPa)
Packaging & Delivery
Packaging Detail:Plastic films
- Q:Why should the high pressure hydraulic tube peel off the outer skin?
- Skinning requirement:The stripping length of hydraulic hose shall be two to four mm shorter than the caseA layer without peeling, more than two layers stripped to see the steel wire, otherwise the shell is easy to fall offThe size of the joints to be installed depends on the size of the joint and the quality of the hose, just start recording more to find the most suitable size.
- Q:What do you mean by "DN" on hydraulic hose?
- Hydraulic hose temperature: -40 ~ 120 DEG C, product specification range: DN2.5mm ~ DN305mm.
- Q:Laboratory condensate water pipe must use rubber tube, shall not use latex tube reasons
- Low temperature bending test at low temperature: hose clamp on rigid torsion wheel diameter hose diameter 12 times, for 6 hours at a low temperature, twisted 180 degrees within 12s when the measured torque and the standard temperature measured torque ratio. Low temperature bending: hose clamped in the diameter of the hose within 12 times the torsion wheel, parked at low temperatures for 24 hours, in the 10s to reverse 180 degrees, check whether or not the internal and external plastic brittle fracture and damage.
- Q:Will the outside of the brake hose of the car burst apart?
- There is a potential safety hazard to the outside rubber skin. It is possible to slam on the brake. The brakes are not trivial, so I suggest you replace them in time.
- Q:What should I pay attention to when rubber tube is in storage?
- Storage should be as follows: (1) should be stored in a ventilated and dry environment, the relative humidity of the air is 50% ~ 80%. (2) should be stored in non corrosive media, and away from the heat source, the temperature is about 5 degrees Celsius conditions. (3) packing should be kept as far as possible without box stacking.
- Q:What does rubber soft joint "KDTF" mean?
- Rubber flexible joint KDTF is a flexible single ball rubber joint.
- Q:Latex tube, rubber tube, silicone tube, which three of the best tightness?
- Rubber tightest is butyl rubber, rubber pipe products in general, with no fiber layer, expanding 300-500% is no problem, you can put it into the glass tube, depends on the strength of the glass tube and technique.
- Q:The difference between the rubber pipe and PE pipe
- The characteristics of the rubber tube has physiological inertia, UV resistance, ozone resistance, resistance to high temperature (-80 to 300), high transparency, strong resilience, resistant to compression permanent deformation, oil resistance, impact resistance, acid and alkali resistance, wear resistance, flame resistance, voltage, electric.
- Q:What is the maximum pressure that a hose can bear?
- This hose with material, wall thickness, diameter is Dudu, but there are special hose pressure testing machine test the size of the market, you take a look at the next.
- Q:What is a rubber core pulling method?
- When using the core pulling method, the hole is usually made of 5 - 7 layers of canvas and 6 - 7mm thick rubber tube. The hose can be used for retaining the straight lines, curves or broken lines.
CYTRUBBER, specially produces wire braided rubber hose,spiral rubber hose,super high pressure rubber hose,pneumatic hose,sand blast hose,oxygen blowing hose,drilling hose,hydraulic cylinder,metal hose and various rubber products.With the merits of high pressure resistance,small bending radius,strong fatigue resistance,long lifespan and so on,our products are widely used in metallurgy,oil drilling,engineering machines,mining,various hydraulic machines and etc.
1. Manufacturer Overview
|Annual Output Value
||Above US$ 1.5 Million
||Mid East, Africa, Europe, America
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
||English; Chinese; Spain; Alabic
||Above 15,000 square meters
|No. of Production Lines
||OEM Service Offered; Design Service Offered
|Product Price Range