Product Description of Silicone Rubber Hose
We can offer high performance silicone rubber hose.
1.Materials:High quality silicone
2.Quality manager system:ISO/TS16949
We provide high quality silicone rubber hose:
For car cool air intake
Advantage: Good aging resistance and good ozong resistance, good organic solvent resistance property.
Work temperature: Under 300 °C.
Tensile Strength: Minmum: 10Mpa,
Elongation at break: Minmum: 300%
Price will be good and quality will be good!Please contact us if you need those kinds of rubbe hose.We
will offer our best service!This is danis lee.Welcome to your inquiry
- Q:Rubber car Block for parking spaces. Where is the parking space?. What is the size of one side of the parking space?
- In fact, there is a relatively simple way to curb parking, that is, in front of the entire parking lot in front of the flat car in front of the line, according to the distance between the two vehicles, the width of the road and parking spaces set length. Then turn the steering wheel close to the point position back to the right until the front of the car close to the front right corner of the car, the left rear corner, the steering wheel starts to rotate. Initially, the steering wheel rotates slowly, when the front bumper in the front of the car leaves the steering wheel to the left, near the point position. From the left rear view mirror, the left rear side of the upper left corner of the car is aligned with the car, and the steering wheel is quickly reversed and stopped. The rest is just right. The car can be parked in the middle of the parking space.
- Q:What are the applications of rubber airbags in the automotive field?
- In automotive shock absorber products, suspension, shock absorbers, airbags, etc. are included. High performance liquid filled engine pad and axle sleeve are the representative achievements in the development of new automotive rubber products in recent years. The high function liquid filled engine pad and shaft sleeve are made of rubber elastomer as a fluid sealing film, and the rubber spring deforms when it vibrates so as to act as a buffer. Automobile safety airbag is made of rubber and rubber started to develop in 1970s, 90s new product to obtain a composite application, now not only in the driver's seat, but also installed in gallery assistant.
- Q:How to properly clean automobile engines, rubber and tires and other parts?
- The procedures for cleaning and beautifying the engine are as follows:(1) before scrubbing, remove dust or fine sand with a brush or jet gun.(2) be sure to spray detergent onto a sponge or brush before wiping it.(3) the black resin parts can be cleaned and protected by plastic parts, so that the wax can be renewed. If it is sprayed directly, it may be sprayed into the place where it should not be sprayed.
- Q:How can a soft rubber bar be machined on a lathe? The hole drilled by the drill hole is triangular
- Grinding tool, angle grinding, edge sharpening, flutes to open large and deep, the image that is cutting the same effect formed in the contact surface. High speed, small knife, finally finishing with the cutter grinding sharp after finishing, finishing allowance not more than 30.
- Q:How to determine the service life of car tires? A new pair of tires is how to use the length of time or number of kilometers to judge?
- The service life of tires is generally about 2 6W kilometers, depending on the vehicle running conditions and the use of the environment.The road is flat and the tyre will last longer.
- Q:How do I fix the car wiper strips?
- Check wiper method is very simple, some spray cleaning liquid, and then start the wiper, notice the action is smooth, hear if there is a "scratch" sound, if any, said too much pressure to the glass wiper, must make the appropriate adjustment and correction. When the wiper Saowan one to two, to see whether there is water on the windshield, and observe whether it will leave scratches, if you see clearly what is said on the wiper wiper blade has been aging, should be replaced with new rubber strips.
- Q:Are car tires poisonous?
- Waste tires can be directly crushed and made into rubber powder to pave roads, which can save a lot of asphalt. After the desulfurization production of reclaimed rubber, used in the production of rubber hoses, rubber mats, etc., can also be added to a new proportion of the new tires, a large number of natural rubber and synthetic rubber can be saved
- Q:How do I remove the glue from my car floor mats?
- Latex car mats using for a long time, because the bacterium, cause odor increase, so the depth of the cleaning work is very necessary, the best cleaning method of latex car mats, detergent, fruit is the best goods scented detergent, do not use detergent washing powder and other strong corrosive. That will only make the latex mat gradually yellow and not up to going to taste the effect.Through the introduction of the above methods, the owners buy new car mats, odor can be removed basically. In addition, pay attention to buy high-quality latex made from mats.
- Q:What is the ratio of carbon black in automobile tire rubber?
- Many kinds of rubber products, operating conditions and performance requirements are different, according to the main function of products are adhesive tape, rubber hose, rubber plate, rubber products, rubber seals, rubber roller, conductive or anti-static rubber, hard rubber, rubber shoes and other categories of products, and each kind of rubber products, and according to the conditions of use and use divided into several varieties. In order to meet the performance of various products and service requirements, personnel from the use of rubber, rubber vulcanization system and reinforcing filling system, softening system, anti-aging system and 3252 arts system, choose the reasonable formula, various additives and process conditions, meet the product performance requirements.
- Q:Installation method of automobile door glass sealing strip
- This is to go to the 4S shop, the average person is not installed, because the door has radian, there is no specific tool, it is difficult to install. If it doesn't fit, it rains and the water gets in. It's a lot of noise. And you buy the sealing strip, but also the specific thickness of the sheet metal on the door may not be consistent.
Our continuous vulcanization extrusion equipment, which vulcanizes extruded rubber through a microwave process, is the most technologically advanced equipment for curing continuous lengths of extruded rubber. As a result of this process, closer tolerances are maintained. In addition, Microwaved extruded rubber products are very cost-effective, long lengths are typical. In line cutting is another available option to maintain the lowest possible costs.. Please feel free to contact us for cooperation.
1. Manufacturer Overview
|Annual Output Value
||US$2.5 Million - US$5 Million
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||91% - 100%
|No.of Employees in Trade Department
||5,000-10,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range