Series 1,3,5,8 Aluminum Coils and Sheets Mill Finished

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT or LC
Min Order Qty:
5 m.t.
Supply Capability:
9000 m.t./month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Aluminium is a relatively soft, durable, lightweight, ductile and malleablemetal with appearance ranging from silvery to dull gray, depending on the surface roughness. It is nonmagnetic and does not easily ignite. A fresh film of aluminium serves as a good reflector (approximately 92%) of visible light and an excellent reflector (as much as 98%) of medium and far infrared radiation. The yield strength of pure aluminium is 7–11 MPa, while aluminium alloys have yield strengths ranging from 200 MPa to 600 MPa. Aluminium has about one-third the density and stiffness of steel. It is easily machined, cast, drawn and extruded.

 

Alloy:  AA1050, 1060, 1100, AA3003, 3005, 3015, 5052, 5754, 5083,8011,etc

Temper:H14/16/18/22/24/32,HO etc.

Thickness:0.2mm—100mm

Width:100mm—2300mm (Can be slitted)

Inner Diameter: 508MM

CoilWeight:500kg-3000kg(Max.)

Application: Foil stock, Circles, Roofing, Canstock, Marine plate,Anti-sliperypurpose in vehicles, packing and appliance.


Chemical Composition and Mechanical Properties

                     CHEMICAL    COMPOSITION   (Max)         

Si

Fe

Cu

Mn

Gallium

Cr

Boron

Zinc

Ti+Van

0.10

0.40

0.05

0.01

0.03

0.01

0.05

0.05

0.02

  UTS  

 (Mpa)

ELONGATION 

  

         At temperature of 20 deg. c 

RESISTIVITY Ω·mm²/M, max

CONDUCTIVITY%IACS,  min

59--135

 20%  Min

        0.028035

      61.5

Packaging & Delivery

Packaging Details:

strong export packing, eye to wall, eye to sky, as demand

Delivery Detail:

within 15-20days after confirmation

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What is the formula to calculate the wall thickness of aluminum coil?
Aluminum coil thickness*aluminum coil width*aluminum coil curl*aluminum density (the density of aluminum alloy: 2.73, the density of pure aluminum: 2.71)
Q:What’s the loss rate per kg when processing aluminum coil to aluminum sheet?
6.5kg/piece
Q:How many 1220mm*2440mm aluminum sheets can one-ton aluminum coil be sliced to? Thank you.
If it is 1.0mm thick, the coil can be sliced into 124 pieces. For other thickness, please use 124 divide the thickness.
Q:Why the aluminum-plastic panel processed by color aluminum coil peel off paint?
Generally speaking, aluminum-plastic panel will not peel off paint. If it does happen, the quality of the aluminum-plastic panel is very poor.
Q:How is the welding performance of 3003 aluminum coil?
3003 aluminum coil, a kind of rust-proof aluminum, belongs to AL-Mn series alloy. With low intensity (slightly higher than commercial purity aluminum), it cannot endure heat treatment, so cold processing is adopted to increase its mechanical property: high plasticity in annealing and semi-cold hardening, low plasticity in cold hardening, good corrosion resistance., good weldability and bad machinability. It is mainly used for low load part in liquid or gaseous medium requiring high plasticity and good weldability, such as fuel tanks, gasoline or lubricant conduit. It can also be used for liquid containers and other deep drawing small load parts made by deep drawing. Aluminum wire can be used to make the rivet.3003 aluminum sheet has good formability, weldability and corrosion resistance. It is used to process parts which require good formability, corrosion resistance and weldability and lower intensity than 1xxx series alloy, such as such as kitchenware, food and chemical products processing and storage equipment, groove and tank to transport liquid product, pressure vessel and pipe processed from thin plate, cooling fin, make-up board, photocopier rollers and ship material.
Q:Why are the aluminum coils sticky after annealing?
There is oil or the annealing time is too long!
Q:Why does fillet appear when rolling aluminum coil?
How thick and wide is it when there is such problem? Which is the rolling pass? And what is the type of the rolling mill? The simple 4 rollers or CVC and HC rolling mill with roller control. Does the filler appear in rolling or out of roller? Different thickness will lead to different analysis.
Q:How much cube is the 0.9mm aluminum rolling?
This is a common problem. Anyone who had received high school education can calculate it very quickily. One way is to calculate sectional area with circular area, then times the thickness of the aluminum rolling. Another way is to use the outer diameter circular area to subtract the core area and then times the thickness of aluminum rolling.
Q:How does aluminum ingot be processed to aluminum coil (aluminum sheet)?
This depends on what aluminum ingot is. Small ingot needs to be casted into big one by putting into the melting furnace, and then be rolled to aluminum coil through rolling mill.
Q:Why does the end face of aluminum coil have grease spots?
Process one without coolant to see whether there are spots. There is a layer of alumina membrane on the blank face of aluminum coil, which will react with basic coolant when heating through processing.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range